Votes - 2, Average rating: 3 ( )

Manafacture: Zanussi File size: 1.45 mb File name: Language of manual:

Cleaning and Maintenance Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. General cleaning Wash the enamelled components with warm soapy water. Never use abrasive cleaners. Frequently wash the "caps" and the "crowns" with hot soapy water, carefully taking away any built-up of food. Regularly wipe over the hob top using a soft cloth weel wrung out in warm water to which a little liquid detergent has been added. Avoid the use of the following: -household detergent and bleaches; -impregnated pads unsuitable for non-stick saucepans; -steel wool pads; -bath/sink stain removers. Should the hob top become heavily soiled, it is recommended that a proper cleaning product is used. Pan supports The pan supports are dishwasher proof. If the marks are particularly difficult to remove, use common non-abrasive cleaners or specific products. Never use steel wool pads or acids. Ignition candle The electric ignition is obtained through a ceramic Fig. 3"candle" and a metal electrode (Fig.1-2 lett. C). Keep these components well clean, to avoid difficult lighting, and check that the burner crown holes are not obstructed. Cleaning of the hotplates Spills on the hotplates should be removed using warm water and a soft cloth. Alternatively, wipe the plates with a drop of olive oil on a kitchen towel (while the plates are still warm). Periodic Maintenance Periodically ask your local Service Centre to check the conditions of the gas supply pipe and the pressure adjuster, if fitted. To ensure the good operation of the hob and its safety features, it is necessary that the taps are periodically lubricated. FO 2110 Technical Data Gas Burners Rating Rapid Burner 3,0 kW (G20) - 2,8 kW (G30/G31) Semirapid Burner 2,0 kW Auxiliary Burner 1,0 kW Appliance Class 3 Category II2H3B/P Setting Natural gas G20 -20 mbar Gas connection G 1/2" Electric hotplate (ZXL 636) O 145 mm. 1,5 kW Electric Supply 230 V ~ 50 Hz Hob recess dimensions Length 550 mm. Width 470 mm. Instruction for the Installer • The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force. • The side walls of the unit in which the hob is going to be installed, must not exceed the height of the working top. • Avoid installing the appliance in the proximity of inflammable materials (e.g. curtains, tea towels etc.). • The appliance must be electrically disconnected before all interventions. If any electric supply to the appliance is required to carry out the work, ensure all the necessary precautions are followed. THE MANUFACTURER WILL NOT ACCEPT LIABILITY, SHOULD ANY OF THE OTHER SAFETY INSTRUCTIONS INCORPORATED IN THIS BOOK OR THE REGULATION IN FORCE BE IGNORED. Fig. 4FO 0264 A) Ramp with ending nut B) Seal C) Adjustable connection Gas connection Choose fixed connections or use a flexible pipe in stainless steel in compliance with the regulation in force. If using flexible metallic pipes, be careful they do not come in contact with mobile parts or they are not squeezed. Use the same attention when the hob is combinated with an oven. IMPORTANT -To ensure a correct operation, a saving of energy and the long-life of the appliance, the voltage pressure of the appliance must correspond to the recommended values. The adjustable connection is fixed to the comprehensive ramp by means of a threaded nut G 1/2". Interpose the sealing between the components as shown in Fig. 4. Screw the parts without forcing, adjust the connection in the required direction and tighten everything. IMPORTANT - When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Use some soapy water, never a flame. Electrical Connection The appliance is designed to be connected to 230 V monophase electricity supply. The connection must be carried out in compliance with the laws and regulations in force. Before the appliance is connected: 1) check that the main fuse and the domestic installation can support the load (see the rating label); 2) check that the power supply is properly earthed in compliance with the current rules; 3) check the socket or the double pole switch used for the electrical connection can be easily reached with the appliance built in the forniture unit. The appliance is supplied with a connection cable. This has to be provided with a proper plug, able to support the load marked on the identification plate. The plug has to be fitted in a proper socket. If connecting the appliance directly to the electric system, it is necessary that you install a double pole switch between the appliance and the electricity supply, with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current rules. The connection cable has to be placed in order that, in each part, it cannot reach a temperature 90 °C higher than the room temperature. The brown ...

Download now

Please, enter two numbers from picture: