Votes - 2, Average rating: 4
(
)
)
|
manual abstract
Den indbyggede netdel er derfor tilsluttet til lysnettet sà længe netstikket sidder i stikkontakten, Norsk Typeskilt finnes pâ apparatens underside. Observer: Nettbryteren er sekundert innkoplet. Den mnebygde netdelen er derfor ikke frakoplet nettet sâ lenge apparatet er tilsluttet nettkontakten. 2 ALARM 2 UP A £ SLUMBER 3 English OPERATION WHICH BUTTONS ARE WHERE ? © ALARM 1 - to set alarm time 1 © ALARM 2 - to set alarm time 2 © DOWN - fast ^ and slow ▼ backward © UP - fast ^ and slow -*• forward © TIME - to set time © SLUMBER - to slumber/set slumber time © REPEAT ALARM/SLUMBER OFF repeat alarm - to switch off alarm temporarily slumber off - to switch off slumber function © BAND - for waveband selection © TUNING - for station selection © VOLUME - to adjust sound level © INDICATOR 2 - alarm 2 is switched on © INDICATOR 1 - alarm 1 is switched on © alarm switch ALARM 1 - to wake by radio at alarm time 1 ALARM 2 - to wake by buzzer at alarm time 2 1 +2 - to wake at alarm time 1 by radio and at alarm time 2 by buzzer © function switch AUTO - alarm is switched on RADIO ON - radio is switched on OR1 - radio and alarm are switched off This appliance conforms to the radio interference suppression requirements of the European Community. The type plate is located on the base of the appliance. MAINS CONNECTION ¡Ql_ Checkif the mains vo'tage as shown on the type plate on the base of the set corresponds to your local mains supply. If it does not, consult your dealer or service organisation As soon as you insert the mains plug into the wall socket, the figures on the display will blink. This means that you must set the correct time. To disconnect the set from the mains completely, withdraw the mains plug from the wall socket. Important note for users in U.K.: When fitting a mams plug to the moms lead proceed as foVo.'.c- The v..res in the mains lead are co'oured m accordance v.itft iiv folfo/.mg cods Slue- Neuiral, Bro/.n U.e Tr^secoIoursmaynofcorrespondv.ithtteco'.ourmirfjngsiG'i'ritifvni the terminate m your plug, to proceed as folfo.’.s Connect the 8ro.\n v.ire to the terminal marked L or colour«, d ft. cj Connect the 8iue v.ire to the terminal marked N or coloured Bhc'. No connection is necessary to the earth terminal Note: This apparatus must be protected by a 3 Amp Fuse ifa 13 Amp plug is used or, if any other type of plug isused.byaSAmpFuiC' ciin.r in the plug or adapter or at the distribution board If In doubt consult a qualified electncan lVamtng\\rnen this umt is not in use and also before attempts i intern ‘it examination, remove the mams plug from the wall soefcet CLOCK Clock display The clock display shows the time. The display also indicates whether you have switched on the alarm If alarm 1 ison,thenlNDICATOR©lightsup,Foralarm 2 INDICATOR ©lights up and for the dual alarm both light up. Appliances provided with a 12-hour clock system Appliances provided with a 12-hour clock system have an PM-mdtcator. In case of PM, the PM-indicator will light up (on = PM, off=AM). Setting the time • Keep TIME button © depressed and set the correct time as follows: - Fast and slow forward with the UP ± + •*■ buttons - Fast and slow backward with the DOWN buttons ©. 4 OPERATION ALARM Alarm time If you wish to use the alarm, then you should first of all set the alarm time. The alarm time is the time when you wish to be woken up. You may set two different alarm times. This can be useful if, for example, you need to be woken at a different time during the week than at the weekend. Note: With alarm 1 you will always be woken by the radio and with alarm 2 by the buzzer. During the week, for example, you may choose to be woken by the buzzer (alarm 2) and at the weekend by the radio (alarm 1). Setting alarm time 1 • Press ALARM 1 button Q. The display will now show alarm time 1. • Keep button Q depressed and set the required alarm time with the UP ±+-*- buttons ©and DOWN buttons ©. • Release ALARM 1 button Q. The display will again show the correct time. You can check alarm time 1 by simply pressing button Q. Setting alarm time 2 • Press ALARM 2 button ©. The display will now show alarm time 2. • Keep button © depressed and set the required alarm time with the UP © and DOWN ^+'*' © buttons. • Release ALARM 2 button ©. The display will again show the correct time. You can check alarm time 2 by simply pressing button ©. ALARM ON Switching on alarm 1 • Set function switch © to AUTO and the alarm function is switched on. • Select ALARM 1 with alarm switch © On the display INDICATOR © will light up. You have now switched on alarm 1. • At the set alarm time 1 you will be woken by the radio. Switching on alarm 2 -Q. • Set function switch @ to AUTO and the alarm function is switched on. • Select ALARM 2 with alarm switch © On the display INDICATOR © will light up. You have now switched on alarm 2. • At the set alarm time 2 you will be woken by the buzzer. Switching...