11. Never look directly into the Spotlight. 12. Avoid touching the Lens as it may become hot during operation. 13. Do not dissassemble the Battery or remove any parts from the Battery and surrounding connections. 14. Do not allow the Spotlight to be exposed to fire or high heat as this may result in an explosion. 15. Disconnect power. Unplug charger when not in use. 16. Maintenance. For your safety, maintenance should be performed regularly by a qualified technician. Warning: The warnings, cauti

For future reference, please complete the owner’s record below: __________ Serial No.___________ Purchase Date______________ SAVE THE RECEIPT, WARRANTY AND THESE INSTRUCTIONS. It is important that you read the entire manual to become familiar with the unit BEFORE you begin assembly. Technical Specifications Tool Name: Spotlight, 1,000,000 Candle Power Item Number: 42417 Housing Diameter: 6" Battery: 12 VDC Lens Adapter: 5" Lens Construction: 3/16" Glass Candle Power 1,000,000 Light Source: Quart

Symbology Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. V~ Volts Alternating Current A Amperes n0 xxxx/min. No Load Revolutions per Minute (RPM) Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. SPECIFIC SAFETY RULES WARNING: When using outdoor use portable lamps, basic safety precautions shou

A Battery that gets too hot can be permanently damaged. Never over- discharge a Battery by using the tool even after tool performance is decreasing.When tool performance begins to diminish, stop the tool, and recharge the Battery. 13. Always remove the Battery from the Spotlight before performing inspection, maintenance, cleaning procedures, or storage. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that

If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. Operating Instructions Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. To prevent serious injury from accidental operation: Turn the Power Switch to its off position and disconnect the Adapter Cord from its electrical supply source before per

First remove the worklight from the vehicle, place it on the ground with a soft cloth or rag under it. 2. The glass Lens is held in by the rubber lip of the light housing. To remove it peel back the rubber lip of the Worklight then pull out the glass lens. CAUTION: The glass lens is difficult to remove. If you are not comfortable doing this it should be done by a qualified service technician. 3. Once the lens is out remove the H3 bulb and replace it. You will not need any tools to remove and r

Symbology Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. V~ Volts Alternating Current A Amperes n0 xxxx/min. No Load Revolutions per Minute (RPM) Specifications Electrical Requirements 120 V~ / 60 Hz / 3.9 A Bulb 500W / 120 V~ Halogen (included) E229796 Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as p

Do not leave the Light unattended 2. when it is plugged into an electrical outlet. Turn off the Light, and unplug it from its electrical outlet before leaving. This product is not a toy. Keep it out 3. of reach of children. People with pacemakers should 4. consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure. In addition, people with pacemakers should: • Avoid operating alone. • Properly mainta

(See Figure C.) 5. If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum cord size. (See Figure C.) 6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use. 7. Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified ele