Votes - 3, Average rating: 4.7 ( )

Manafacture: Toshiba File size: 3.55 mb File name: Language of manual:

To avoid damaging the memory module, be careful not to touch its pin connector on the side you insert into the computer. 9 Remove the new memory module from its antistatic packaging. Avoid touching the connectors on the memory module or on the computer. Grease or dust on the connectors may cause memory access problems. 10 Insert the memory module into the socket on the underside of the computer. Sample inserting the memory module into the slot Getting Started 59 Adding memory (optional) 11 Hold the memory module by its edges so that the gold connector bar faces the slot, at a slight angle to the socket. clip clip Sample inserting the memory module into the socket 12 Check that the module is inserted completely into the socket and lined up squarely with the socket clips. Sample aligning the module into the socket 60 60 Getting Started Adding memory (optional) 13 Gently press down on the memory module connector until the clips snap into place. clip clip Sample pressing down on the memory module Do not force the memory module into position. The memory module should be completely inserted into the socket and level when secured in place. The clips on either side of the memory module snap into place when the memory module is properly inserted. 14 Replace the memory module slot cover and tighten the screw. 15 Re-insert the battery. For more information on inserting the battery, see “Changing the main battery” on page 116. 16 Turn the computer right side up. 17 Reconnect the cables. 18 Restart the computer. TECHNICAL NOTE: You must have at least one memory module installed for the computer to work. You can now continue setting up the computer. When the operating system has loaded, you can verify that the computer has recognized the additional memory module. Getting Started 61 Adding memory (optional) If you are adding an extra memory module after setting up the computer, verify that the computer has recognized it correctly as described in “Checking total memory” on page 62. Removing a memory module If you need to remove a memory module: 1 Complete steps 1–8 in “Installing a memory module” on page 55 to shut down the computer and open the memory module slot cover. Do not try to remove a memory module with the computer turned on. You can damage the computer and the device. Do not remove the memory module while the computer is in Standby or Hibernation mode. The computer could hang up the next time you turn it on and data in memory will be lost. In either of the above cases, the Standby configuration will not be saved. The following message appears when you turn on the power: Warning: Resume Failure Press Any Key To Continue If the computer hangs up when you turn it on, perform the following: Press the power button and hold it down for at least ten seconds, then turn the power on again. 2 Pull the clips away from the memory module. The memory module pops up slightly. 3 Gently lift the memory module to a 45 degree angle and slide it out of the slot. 62 62 Getting Started Adding memory (optional) Sample removing the memory module 4 Replace the memory module slot cover and tighten the screw. 5 Turn the computer over and restart it. TECHNICAL NOTE: You must have at least one memory module installed for the computer to work. Checking total memory When you add or remove a memory module, you can check that the computer has recognized the change. To do this: 1 Click Start, Control Panel, Performance and Maintenance, and then System. 2 The General tab view automatically appears and shows total memory. If the computer does not recognize the memory configuration, turn off the computer, remove the memory slot cover, and make sure the memory module is seated properly, as described in step 13 of “Installing a memory module” on page 55. Getting Started 63 Using the TouchPad™ Using the TouchPad™ The TouchPad, the small, smooth square cutout located in front of the keyboard, is sensitive to touch and enables you to move the cursor with the stroke of a finger. Simply move your finger on the TouchPad in the direction you would like to move the cursor: . To move the cursor to the top of the page, push your finger forward on the TouchPad. . To move the cursor to the bottom of the page, drag your finger toward yourself. . To move the cursor to the right side of the page, slide your finger across the TouchPad from left to right. . To move it to the left side, slide your finger from right to left. NOTE Because the TouchPad is much smaller than the display screen, moving your cursor across the screen often means having to move your finger several times across the TouchPad in the preferred direction. Once you have positioned your cursor, you can click it into place by either double-tapping the TouchPad or clicking the control buttons. Scrolling with the TouchPad™ There are two active regions on the TouchPad that allow you to scroll as you would with any wheel device on a mouse or trackball. To scroll vertically, run your finger up or down alon...

Download now

Please, enter two numbers from picture: