Votes - 4, Average rating: 4
(
)
)
|
manual abstract
Using this system (expansion card and connector box) in combination with specific software, two sets of MIDI INs and MIDI OUTs become available. Since it can also handle SMPTE timecode, synchronization to timecode compatible multi-track tape recorders and VTRs is also possible. * IBM and IBM AT are registered trademark of the International Business Machines Corporation. ■ Inportant Notes [Power Supply] •When making any connections with other devices, always turn off the power to all equipment first; this will help prevent damage or malfunction. [Placement] • Do not subject the unit to temperature extremes (eg. direct sunlight in an enclosed vehicle). Avoid using or storing the unit in dusty or humid areas or areas that are subject to high vibration levels. [Maintenance] •Never use benzine, thinners, alcohol or solvents of any kind, to avoid the risk of discoloration and/or deformation. [Additional Precautions] •Protect the unit from strong impact. •Do not allow objects or liquids of any kind to penetrate the unit. In the event of such an occurrence, discontinue use immediately. Contact qualified service personnel as soon as possible. •Should a malfunction occur (or if you suspect there is a problem) discontinue use immediately. Contact qualified service personnel as soon as possible. iPanel Description »MIDI OUT A/В Sockets Connect the MIDI IN socket of an instrument ( eg., sound module ) to either of these MIDI OUT sockets. (Connect one instrument to each socket if two instruments are being used.) «¡Ma gpjis Roland ». TfUiaENTMlOtPnOCeSSlNGiWT Super MPU •MIDI IN A/В Sockets Connect the MIDI OUT socket of an instrument (eg., MIDI keyboard) to either of these MIDI IN sockets. (Connect one instrument to each socket if two msturments are being used.) ^•Interrupt Line Selector Switch / .•I/O Address Selector Switch / •Connector Box Input Port Connect the supplied Connector Box to this port. HBIII ► SMPTE Timecode IN/OUT Jacks To synchronize the S-MPU/AT's sequencer software to a multi-track tape recoder or VTR, input/output SMPTE Timecode through these jacks. Copyright 1992 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. 2605033200 '92-5-BIE1-11SEÍD) ■Using MPU-IPC(-T) compatible software You can also use software that is compatible with the MPU-IPC(-T) on the S-MPU/AT. When the software is booted up, the S-MPU/AT will automatically select the compatible mode. However, many of the functions of the S-MPU/AT will be disabled. • Functions expanded with the S-MPU/AT MIDI IN : Use MIDI IN A. No MIDI messages will be received through MIDI IN B. MIDI OUT : The same MIDI messages are transmitted through both the MIDI OUT A and B sockets. SMPTE Timecode : Cannot be used. ■ Functions of the MPU-IPC(-T) FSK Sync : Cannot be used. (The S-MPU/AT does not feature TAPE IN/OUT jacks.) The Metronome Function : Cannot be used. (The S-MPU/AT does not have this function.) ■Interrupt Line and I/O Address •Pre-programmed Settings Interrupt Line: IRQ2 I/O Address Mode Address Read Write Bus 401 0330h Data Data 8 bit 0331 h Status Command Native 0332h Immediate Message/Function Immediate Message/Function 16 bit 0334h Sequence Message/Function Sequence Message/Function 0336h Monitor Interrupt to Super MPU 0338h Status Interrupt Mask •To change the Interrupt Line and I/O Address To change the Interrupt Line or I/O Address, be sure to switch the computer off. IRQ1 IRQ10—* IRQ 9- ( Pre-programmed Settings) IRQ 7—' L The Interrupt Line can be changed using the Interrupt Line Selector Switch on the panel of the expansion card. * When set to INT 5-9, no interrupt request will occur. IRQ 5 The I/O Address can be changed using the I/O Address Selector Switch on the panel of the expansion card. * To change the switch positions, carefully use a rigid, pointed object (a pen, for example). * The 6th switch can be set to either On or Off. Note : Never put anything on the printed circuit board or touch the components with your bare hands. 133x 137x 13Bx 13Fx ■Installing the S-MPU/AT Expansion Card 1. Switch the computer off and unplug it from the AC source. 2. Remove the cover from the computer. 3. Carefully insert the S-MPU/AT card (components facing upward) into an available card slot. Insert it using the card guide of the expansion slot. Secure the S-MPU/AT's panel to the computer with the supplied screws. * You can install the S-MPU/AT card in any available slot. Note : Never put anything on the printed circuit board or touch the components with your bare hands. •Dimensions Expansion Card : 23 (W) X 198 (D) X 126 (H) mm 15/16 (W) X 7-13/16 (D) X 5 (H) inches Connector Box : 165 (W) X 50 (D) X 34 (H) mm 6-1/2 (W) X 2 (D) X 1-3/8 (H) inches • Weight Expansion Card : 160 g / .3 lbs Connector Box : 340 g / .75 lbs •Accessories Owner's Manual * For a detailed tech...