Votes - 2, Average rating: 4 ( )

Manafacture: Peavey File size: 1.63 mb File name: df5a913e-9ca3-400b-beff-a49a01754b9b.pdf Language of manual:

If hum or noise is present with the ground switch in the center position, place the ground polarity switch to positive or negative (+ or -) to minimize hum; should a problem continue, consult your authorized Peavey dealer, the Peavey factory, or a qualified service technician. Note: The ground switch is not functional on 220/240 volt models. RESET/CIRCUIT BREAKER SWITCH (28) Use this switch to restore power to your unit when the internal breaker is tripped. The proper method is to turn the power switch to the “off” position before resetting the breaker. To reset, push the reset button in and release it. Turn the unit back on and confirm that the power LED is on. If the breaker is tripped again upon power-up, consult your authorized Peavey dealer, the Peavey factory, or a qualified service technician. POWER SWITCH (29) This switch is used to turn the FireBass 700 on or off. To turn the unit on, flip the switch to the “on” position. IEC CONNECTOR/DETACHABLE LINE CORD (30) For your safety, we have incorporated a detachable, three-wire line (mains) cord with proper grounding facilities. It is not advisable to remove the ground pin under any circumstances. If it is necessary to use the amp without proper grounding facilities, suitable grounding adaptors should be used. Greatly reduced shock hazard exists when the unit is operated with properly grounded receptacles. Connect the IEC plug of your cord to the IEC socket on the rear of your unit. Refer to the back of your unit for the proper voltage required before connecting to a power receptacle. POWER CORD RETAINERS (31) Use the Power Cord Retainers to wrap and store your cable while storing or transporting your FireBass 700. It is best to disconnect the cord from the unit before wrapping. SPEAKER OUTPUT JACKS (32) These two 1/4" jacks provide the powered signal from the amplifier. Each connector is electrically the same (in parallel). Use one of the jacks to connect your speaker cabinet and the other to add a second speaker cabinet in parallel. The minimum speaker load impedance is 2 ohms (or two 4 ohm speakers in parallel). Warning: To prevent the amplifier from overheating, the front fan and rear-located vents should always remain clear of obstructions. REAR PANEL 27 28 31 31 29 30 32 FIREBASS™ 700 SPECIFICATIONS POWER AMPLIFIER SECTION Maximum Input Level: Slope: Rated Power and Load: 700W RMS into 2 ohms 475W RMS into 4 ohms 275W RMS into 8 ohms Power @ Clipping (Typically): (1 kHz, 120 VAC line) 490W RMS into 4 ohms @ 1% THD 550W RMS into 4 ohms @ 5% THD Frequency Response: -1 dB, 20 Hz to 30 kHz @ 400W RMS into 4 ohms Total Harmonic Distortion: Less than 0.25%, 100 mW to 450W RMS, 20 Hz to 10 kHz, 4 ohms (typically below 0.1%) DDT™ Dynamic Range: Greater than 20 dB DDT™ Maximum THD: Below 0.5% THD for 3 dB overload Below 1% THD for 13 dB overload Hum and Noise: Greater than 90 dB below rated power Power Consumption: 1,200W @ 120 VAC 50/60 Hz PREAMP SECTION: The following specs are measured @ 1 kHz with the Low, Mid & High EQ @ 0 dB; Contour @ 0; Mid Shift @ 1 kHz; Input Pad & Bright switch out (off); Post Gain @ 10; Nominal levels are with Pre Gain @ 5; Minimum levels are with Pre Gain @ 10. Passive Preamp Input (Input Pad switch “out”): Impedance: High Z, 220k ohms Nominal Input Level: -27 dBV, 45 mV RMS Minimum Input Level: -48 dBV, 4 mV RMS +10 dBV, 3V RMS Active Preamp Input (Input Pad switch “in”): Impedance: High Z, 68k ohms Nominal Input Level: -17 dBV, 135 mV RMS Minimum Input Level: -38 dBV, 12 mV RMS Maximum Input Level: +20 dBV, 10V RMS Preamp Output: Load Impedance: 1k ohms or greater Nominal Output Level: 0 dBV, 1V RMS Maximum Output Level: +20 dBV, 10V RMS Power Amp Input: Impedance: High Z, 22k ohms Designed Input Level: 0 dBV, 1V RMS (Switching jack providing preamp output to power amp input connection when not used) System Hum and Noise @ Nominal Input Level: (20 Hz to 20 kHz unweighted) Greater than 75 dB below rated power Equalization: Low and High: +/-15 dB @ 40 Hz and 7 kHz, shelving Mid: +/-15 dB @ Mid Shift setting Mid Shift: Variable from 200 Hz to 2 kHz Contour: Special EQ voicing Push Bright: +8 dB @ 8 kHz Variable Crossover: Frequency Range: 100 Hz to 1 kHz 12 dB per octave Crossover Low Output: Load Impedance: 1k ohms or greater Nominal Output Level: 0 dBV, 1V RMS Maximum Output Level: +20 dBV, 10V RMS Crossover High Output: Load Impedance: 1k ohms or greater Nominal Output Level: 0 dBV, 1V RMS Maximum Output Level: +20 dBV, 10V RMS Effects Loop: Send Level: -10 dBV, 315 mV RMS Send Load Impedance: 1k ohms or greater Return Level: -10 dBV, 315 mV RMS Return Input Impedance: 220k ohms Tuner Send: Level: Buffered off the Input jack; Dependent on instrument level Load Impedance: 1k ohms or greater Low Z Balanced Line Out: (600 ohm transformer balanced; Nominal levels with Pre Gain & Line Out Level @ 5; Maximum levels with Pre Gain & Line Out Level @ 10) Nominal Pre-EQ Output Level: -20 dBV, 100 mV RMS Nominal Post-EQ Output Level: -...

Download now

Please, enter two numbers from picture: