Votes - 3, Average rating: 5
(
)
)
|
Other manuals for this model:
Home Theater Systems - DAV-DS1000 (2.94 mb)
Home Theater Systems - DAV-DS1000 (2.78 mb)
manual abstract
The indicator on each rear speaker changes as follows: subwoofer power on/data received (green); subwoofer power on/no data (blinks green); subwoofer power off (red). Switch To avoid short-circuiting the speakers Short-circuiting of the speakers may damage the system. To prevent this, be sure to follow these precautions when connecting the speakers. Make sure the bare wire of each speaker cord does not touch another speaker jack or the bare wire of another speaker cord. Examples of poor instllation of the speaker cords Stripped speaker cord is Stripped cords are touching touching another speaker each other due to excessive terminal. removal of insulation. After connecting all the components, speakers, and the AC power cord, output a test tone to check that all the speakers are connected correctly. For details on outputting a test tone, see page 34. If no sound is heard from a speaker while outputting a test tone, or a test tone is output from a speaker other than the one currently displayed in the front panel display, the speaker may be short-circuited. If this happens, check the speaker connection again. Note Be sure to match the speaker cord to the appropriate terminal on the components: 3 to 3, and # to #. If the cords are reversed, the sound will be distorted and will lack bass. Getting Started 23GB continued About the wireless rear speakers This wireless rear speaker system adopts the Digital Infrared Audio Transmission system (page 78). The following diagram indicates the infrared transmission area (the range that the infrared rays can reach). Top view Side view 45° 45° Front speakers Approx. 5 m Approx. 10 m 45° Infrared signal Rear speakers Approx. 5 m 45° 45° 45° Front speakers Approx. 5 m Approx. 10 m 45° Infrared signal Rear speakers Approx. 5 m 45° Notes • When you use the rear speakers in wireless setting, do not install them in a place exposed to direct sunlight or strong light such as an incandescent lamp. Otherwise, the reaching range of the audio signal may be insufficient. • If the room where you place the wireless rear speakers is too big or its ceiling is too high, such as in a big hall, make sure that there is no obstruction such as a person or object in the line of sight that links the top of the front speaker with that of the rear speaker. Otherwise, the sound from the rear speakers may be interrupted. • Mixed signals may result if you use this wireless rear speaker system at the same time as other infrared transmission devices that use 3 MHz - 6 MHz waveband. z If you have to place the rear speakers in a place where the wireless setting is unusable, it is recommended to use the speakers in their wired setting (page 25). 24GB Connecting the rear speakers using the speaker cords (Wired setting) You can also connect the rear speakers using the speaker cord. In this case, you do not need to connect the wireless data output cords to the front speakers. Notes • When you use the speakers in Wired setting, make sure to set “CONNECT” to “WIRED” in “SPEAKER SETUP” (page 33). • When you use the speakers in Wired setting, do not connect the AC power cords to the rear speakers. If the power of the rear speakers is on, no sound is output from the rear speakers. Terminals for connecting the speakers Connect the To the Front speakers SPEAKER FRONT L (white) and R (red) jacks Center speaker SPEAKER CENTER (green) jack Rear speakers SPEAKER REAR L (blue) and R (grey) jacks Front speaker (R) Front speaker (L) TUNER INPUT WIRELESS REAR L R SPEAKER IMPEDANCE USE 4. FRONT L REAR L CENTERFRONT R REAR R FOOT LIGHT HIGH LOW OFF MONITOR OUTPUT COMPONENT VIDEO OUTPUT VIDEO 1 VIDEO L L L Y PB/CB PR/CR R R R VIDEO INPUT AUDIO INPUT S VIDEO (DVD ONLY) SCAN SELECT SELECTABLE INTERLACE SYSTEM CONNECTOR VIDEO 2 VIDEO INPUT AUDIO INPUT VIDEO OUTPUT AUDIO OUTPUT SPEAKER IMPEDANCE USE 4. FRONT L REAR L WIRED SETTING ONLY CENTERFRONT R REAR R Rear speaker (L) Rear speaker (R) Subwoofer Center speaker Getting Started 25GB 26GB TUNER INPUT WIRELESS REAR L R SPEAKER IMPEDANCE USE 4. FRONT L REAR L FRONT R CENTER REAR R FOOT LIGHT HIGH LOW OFF MONITOR OUTPUT COMPONENT VIDEO OUTPUT VIDEO 1 VIDEO L L L Y PB/CB PR/CR R R R VIDEO INPUT AUDIO INPUT S VIDEO (DVD ONLY) SCAN SELECT SELECTABLE INTERLACE SYSTEM CONNECTOR VIDEO 2 VIDEO INPUT AUDIO INPUT VIDEO OUTPUT AUDIO OUTPUT Step 2: Antenna Hookups Joining the tuner Attach the AM loop antenna and the FM wire antenna to the tuner box. Connecting the tuner Connect the tuner to the subwoofer using the supplied tuner cord. Notes • To prevent noise pickup, keep the tuner away from the subwoofer and other components. • Be sure to fully extend the FM wire antenna. • After connecting the FM wire antenna, keep it as horizontal as possible. zIf you have poor FM reception Use a 75-ohms coaxial cable (not supplied) to connect the system to an outdoor FM antenna as shown below. Tuner Tuner cord Outdoor FM antenna Tuner AM loop antenna FM wire antenna North American model Other models Step 3: T...