Votes - 2, Average rating: 4.5
(
)
)
|
Other manuals for this model:
manual abstract
Make sure the iPod/iPhone is updated with the latest Keep the antennas away from the speaker cords and the . The followings are displayed; . Design and specifications are subject to change without notice. signals that are too large. It may take about 10 seconds before “Reading” appears depending . Amplifier section software. If not, update the iPod/iPhone before using AC power cord to avoid picking up noise. remaining playing time for a CD-DA disc track. ID3 tag information for MP3 files when ID3 version 1 and . . on the type of USB device connected. Adjust the volume using the VOLUME or BASS/ European model: If the STANDBY indicator flashes Immediately unplug the AC power cord, and check the following items. Are the + and . speaker cords short-circuited? Is anything blocking the ventilation holes of the system? After the STANDBY indicator stops flashing, reconnect the AC power cord, and turn on the system. If the issue persists, contact your nearest Sony dealer. . . with the system. Turn off nearby electrical equipment. Do not connect the system and the USB device through a USB hub. Power output (rated): 40 watts + 40 watts (6 ohms at 1 kHz, 1% THD) . . . TREBLE to turn off the message. We recommend a .Standby power consumption: 0.5 W Continuous RMS power output (reference): 50 watts + 50 watts (6 ohms at version 2 tags are used (ID3 version 2 tag information display has Because the operation of the system and the iPod/ When the USB device is inserted, the system reads all the files on . volume level where the sound is not blasting out of the 1 kHz, 10% THD) priority when both ID3 version 1 and version 2 tags are used for a the USB device. If there are many folders or files on the USB device, DAB/DAB+ radio station is not received iPhone are different, you may not operate the iPod/ speakers. Music power output (reference): 60 watts + 60 watts (6 ohms at 1 kHz, 10% single MP3 file). it may take a long time to finish reading the USB device. properly (CMT.G1BiP only). iPhone using buttons on the remote or unit. In this THD) Other models: If the “PROTECT” message does not disappear, make With some connected USB devices, after an operation is performed, . case, use the control buttons on the iPod/iPhone. Check all antenna connections, then perform the DAB . sure the speaker cord is connected firmly. there may be a delay before it is performed by this system. Note on the DAB/DAB+ display information Compatibility with all encoding/writing software cannot be Power output (rated): 40 watts + 40 watts (6 ohms at 1 kHz, 1% THD) Automatic Scan procedure (see “Reception of DAB/ . Continuous RMS power output (reference): 50 watts + 50 watts (6 ohms at Push STOP! : You pressed PLAY MODE/TUNING The iPod/iPhone cannot be charged. (CMT.G1BiP only) guaranteed. If audio files on the USB device were originally encoded 1 kHz, 10% THD) DAB+ radio station”). MODE during playback in the CD function. Step Full! : You tried to program more than 25 tracks or If the battery of the iPod/iPhone is empty, the system with incompatible software, those files may produce noise or . The following is also displayed; Input AUDIO IN : Sensitivity 700 mV, impedance 47 kilohms The current DAB/DAB+ service may not be available. Press +/. to select a different service. . interrupted sound, or may not be played back at all. may not be able to charge it even if you connect it to up to 8 characters of service name, up to 128 characters of DLS (Dynamic Label Segment) and up to 16 files (steps). This system cannot play audio files on the USB device in the . the system. In such a case, recharge it with a computer, etc. then connect it to the system. Outputs If you have moved to another area, some services/ . following cases; TIME NG! : The Play Timer start and end times are set to SPEAKERS: Accepts impedance of 6 - 16 ohms characters of ensemble label. frequencies may have changed and you may not be able when the total number of audio files in a folder exceeds 100. . . the same time. CD player section Make sure the iPod/iPhone is connected securely. . . when the total number of audio files on a USB device exceeds A value between 0 and 100 indicating the signal quality to tune into your usual broadcast. Perform the DAB System: Compact disc and digital audio system 10000. You can use the system as a battery charger for iPod/ is displayed. Automatic Scan procedure to re-register the content Laser Diode Properties Emission Duration: Continuous General when the total number of folders on a USB device exceeds 100 . iPhone only when the system is on. of broadcasts. (Performing this procedure clears all (including the “ROOT” folder and empty folders). Laser Output*: Less than 44.6.W Precautions The system does not turn on. previously stored presets.) * This output is the value measurement at a distance of 200mm from the objective lens surface on the Optical Pick-up Block with 7mm aperture. These numbers may vary depending on the file and folder structure. The ri...
Other models in this manual:Home Stereos - CMT-G1IP (667.09 kb)