Votes - 1, Average rating: 5
(
)
)
|
manual abstract
Familiarity with installation and operation procedures will help you obtain the best performance from your new power amplifier. FOR YOUR RECORDS Record the serial number found on the bottom of the unit in the spaces designated on the warranty card and in the space provided below. Refer to the model and serial numbers whenever you call upon your KENWOOD dealer for information or service on this product. Model KAC-8200 Serial number _ CARE & MAINTENANCE • The power source of this unit is exclusively DC 12 V, negative ground. If you wish to mount the unit on a vehicle with DC 24 V, please consult your appointed KENWOOD dealer. • Do not place the amplifier in a place where the amplifier may be exposed to direct sunlight, heat or moisture. 8e careful that metal objects and water do not enter the set. • If you have difficulty in installing the set in your car, please contact your KENWOOD dealer. Cleaning Clean with a dry silicone cloth or a soft colth. The use of thinner, alcohol or other solvents may damage the surface finish. INSTALL A.TIOM * ^len instal',n9 to car, decide the best position by giving proper consideration of the system as a whole and ease of safety. Since the main amplifier has no parts which require operation, it can be installed at a position away from the driver's seat without any hinderances. 8ut deu to its considerable weight, it needs to be installed securely. As generally accepted positions for its installation, places such as under the front seat or inside the trunk, etc. can be considered. • Use screws supplied as accessories when installing the unit. SPECIFICATIONS Specifications subject to change without notice AUDIO Power output ..........95 W/ch into 4 ohms, 1 kHz at 10% THD, ‘Power output...............75 W/ch into 4 ohms, 20 Hz - 60,000 Hz at 0.5% THD, 'Power output..................60 W/ch into 4 ohms, 20 Hz - 60,000 Hz at 0.03% THD, Minimum T.H.D. (1 kHz, 4 ohms)..............0.005% •Frequency Response......5 Hz - 200,000 Hz ( ±3 dB> * Signal/Noise Ratio (A-Weighted)..............100 dB 'Sensitivity (High)................12 mV for 1 W output, 'Sensitivity (Low)...................60 mV for 1 W output, ‘Sensitivity (High)...........100 mV for rated output, ‘Sensitivity (Low)............500 mV for rated output, ‘Minimum Input Inpedance...................10 k ohms General Operating Voltage....... Current Consumption ... Dimentions (W x H x D) Weight................. (' EIA Standard) ...14.4 V (11 V - 16 V) 18.5 A for rated output, .....196x61 x 184 mm ......................2 .0 kg Use the extension cables. CA-18F (1 m), CA-28F (2 m), and CA-48F (4 m) (optional) when the connected models are to be installed away from the main amplifier. • When the installing this unit in the trunk, place it with its heat radiation holes facing upwards to maximize their effect. Do not cover the upper and lower side of heat radiation holes. CONNECTION Extension cable (supplied) KAC-8200 Power supply (red) —»— 0 = ^ ffSI oo81 0 If you hear a noise when starting the engine, connect the line noise filter CN-300 (optional) to the power source (red) of this unit. E=iB-»Yellow - EE>J CN-300 (option) Sensitivity change-over switch (SENSITIVITY) LOW HIGH (0.1 VI (0.5 V) Please set it at the HIGH side About the SZ-20 • Since the power source can be directly obtained from the battery, it provides a stable power source with minimum noise and low voltage drops to maximize the amplifier's performance. • The safety has been provided by use of fusible links, protector tubes and grommets. • Since a power relay is used, it can control a large current volume by the ON/OFF Key Switch. * When SZ-20 is not being used, connect the power supply as follows: KAC-8200 Precautions Since the electrical consumption of this unit is large, obtaining power source from wirings such as those of built-in cigarette lighters will overload the wiring of the car. Make sure to either use SZ-20 (optional) or connect the power source (red) to a position with sufficient current capacity such as the point iimmediately next to the car's main fuse, as shown in the illustration above. (Be sure that the fuse is positioned between the battery and the unit) Before starting to install the set, make sure to remove the negative ( —) terminal of the battery in order to prevent shortcircuiting. When installation and wiring are completed, connect the negative ( — ) terminal of the battery after confirming that there are no errors. When a fuse is blown out, check for any shortcircuiting of cords, and then replace it wit...