Votes - 4, Average rating: 3.8
(
)
)
|
manual abstract
Tips • If you’ve made a mistake, start over from step 1. • Setting the time deactivates the demo mode. If you want to display the demo mode, press DISPLAY/DEMO when the power is off. Note The previous explanation shows you how to set the time while the power is off. To change the time while the power is on, do the following: 1 Press CLOCK/TIMER SET. 2 Turn the jog dial to select SET CLOCK. 3 Press ENTER/NEXT. 4 Perform steps 2 through 5 above. Step 3: Presetting radio stations You can preset the following number of stations: – 2 band model: 20 for FM, 10 for AM. – 3 band model: 20 for FM, 10 for MW, and 10 for SW (or LW, depending on the model you purchased). – 4 band model: 20 for FM, 10 for MW, 10 for LW, and 5 for UKV. (Power) 3 451 2 continued Step 3: Presetting radio stations 3 Press TUNER MEMORY. (continued) A preset number appears in the display. 1 Press TUNER/BAND repeatedly until the band you want appears in the display. The bands you can receive vary depending on the model you purchased. Be sure to check which bands you can receive. Every time you press this button, the band changes as follows: 2 band model: VOLUME ALL DISCS § Preset number 4 Turn the jog dial to select the preset number you want. FM .AM 5 Press ENTER/NEXT. 3 band model: The station is stored. FM nMW nSW n 6 Repeat steps 1 to 5 to store other or stations. FM nMW nLW n To tune in a station with a weak 4 band model: signal FM nMW nLW nUKV* n Press + or – repeatedly in step 2 to tune in the * “STEREO PLUS” is displayed when you select UKV. 2 Press and hold + or – until the frequency indication starts to change, then release. Scanning stops when the system tunes in a station. “TUNED” and “STEREO” (for a stereo program) appear. MONO TUNED STEREO VOLUME station manually. To change the preset number Start over from step 1. To change the AM tuning interval (Except for the European models) The AM tuning interval is factory set to 9 kHz (10 kHz in some areas). To change the AM tuning interval, tune in any AM station first, then turn off the power. While holding down the ENTER/NEXT button, turn the power back on. When you change the interval, AM preset stations will be erased. To reset the interval, repeat the same procedure. Tip ALL DISCS kHz The preset stations are retained for half a day even if MHz . you unplug the power cord or if a power failure occurs. Connecting optional AV components To enhance your system, you can connect optional components. Refer to the instructions of each component. Connecting an MD deck for analog recording Make sure to match the color of the plugs and the connectors. To listen to the sound of the connected MD deck, press FUNCTION repeatedly until “MD” appears. To the audio output To the audio input of the MD deck of the MD deck Connecting audio components Select one of the following two connections, depending on the equipment to be connected and method of connecting. Connecting an MD deck for digital recording You can record from CD into the MD deck digitally by connecting an optical cable. To the DIGITAL IN jack of the MD deck Tip When you connect a Sony MD deck, you can use the MD buttons on this unit’s remote to operate it. In addition, pressing MD awhen the power is off, automatically turns the MD deck on and starts playback if there is a MD in the deck (One Touch Play). Note If you cannot select “MD” even when you have pressed FUNCTION, press while pressing FUNCTION when the power is turned off. “VIDEO” will be switched to “MD”. To return to “VIDEO” do the same procedure. continued Connecting optional AV components (continued) Connecting a super woofer speaker (DHC-MD500 only) You can connect an optional super woofer speaker. To super woofer Connecting a VCR Make sure to match the color of the plugs and the connectors. To listen to the sound of the connected VCR, hold down FUNCTION and press when the power is turned off. This switches the “MD” function to “VIDEO”. Once you enable the “VIDEO” function, just press FUNCTION repeatedly until “VIDEO” appears. To the audio output of the VCR Note If the sound is distorted when selecting “VIDEO”, or you want to switch back to “MD”, repeat the operation described above for switching to “VIDEO”. FM75 AM FM75 AM FM75 AM y75-ohm coaxial cable (not supplied) Screw clamp Ground wire (not supplied) Insulated wire (not supplied) Jack type B Ground wire (not supplied) Jack type B FM75 AM COAXIAL FM75 AM COAXIAL yScrew clamp IEC standard socket connector (not supplied) Screw clamp y Ground wire (not supplied) Important Ground wire (not supplied) If you connect an outdoor antenna, ground from yterminal with the screw clamp. To prevent a gas explosion, do not connect the ground wire to a gas pipe. Connecting outdoor antennas Connect the outdoor antenna to improve the reception. FM antenna Connect the optional FM outdoor antenna. You can also use the TV antenna instead. Jack type A AM antenna Connect a 6- to 15- meter (20- to 50- feet) insulated wire to the AM antenna termin...
Other models in this manual:Home Stereos - DHC-RX707 (588.88 kb)