(1990) Principles of Environmental Physics second edition. Edward Arnold (Hodder & Stoughton). Norman J M & Welles J M (1983). Radiative transfer in an array of canopies. Agron. J. 63:743-748. Norman J M and Jarvis P G (1975). Photosynthesis in Sitca Spruce (Picea sitchensis (Bong) Carr.) V. Radiation penetration theory and a test case. J. Appl. Ecol., 12:839-878 Russel G, Marshall B and Jarvis P (eds). (1989) Plant Canopies, their Growth, Form & Function. SEB Seminar series 31, CUP, Cambridge W

and press .Enter.I key. Then press ! or " key to select .Phase. and also press .Enter. key again. Now, press ! orI " to adjust the monitor untill the noise disappears+ To make sure the .iKey. function performs well, you have to use one of the supported modes. IfI the .iKeyi does not work properly and the .NON PRESET MODE. message is on the OSD, itI means you are not using one of the supported modes. Please set your computer to use one of theI supported modes. You will find a list of supported mo

See: • How to install the monitor on a new computer on page 12. • How to upgrade the monitor on an existing computer on page 13 If you require a User Name and Password to login to your Windows computer, you must be logged on as an Administrator or as a member of the Administrators group in order to install the monitor driver software. Furthermore, if your computer is connected to a network which has security access requirements, network policy settings may prevent you from installing software on

Does the blurring only occur at resolutions lower than the native (maximum) resolution? Read the instructions on the link "Adjusting the Screen Resolution" on the CD. Select the native resolution. Pixel errors can be seen: One of several pixels is permanently black, one or more pixels are permanently white, one or more pixels are permanently red, green, blue or another color. • Clean the LCD screen. • Cycle power on-off. • These are pixels that are permanently on or off and is a natural defect t

AC power input jack 2. DVI-D input socket (Analog-only models do not have the DVI-D input socket) 3. D-Sub input socket Getting to know your monitor 3. How to assemble your monitor hardware If the computer is turned on you must turn it off before continuing. Do not plug-in or turn-on the power to the monitor until instructed to do so. 1. Attach the monitor base. Please be careful to prevent damage to the monitor. Placing the screen surface on an object like a stapler or a mouse will crack the gl

SCC-L07E-A D-1H CHASSIS SPECIFICATIONS 0.25 mm aperture grill pitch Power Consumption 17 inches measured diagonally Maximum 115W 90-degree deflection Nominal 100W, 341 BTU/h (16" maximum viewing image) Deflection frequency Horizontal: 30 to 85 KHz Approx. 329.5 x 243 mm (w/h) Vertical: 50 to150 Hz (13 x 9 5/8 inches) AC input voltage / current 100 to 120 V, 50/60 Hz, 1.8 A Horizontal: Max. 1280 dots 220 to 240V, 50/60Hz, 1A Vertical: Max. 1024 lines (at 75 Hz Refresh Rates) Dimensions 424 x 422

In this sample the memory module in memory slot 1A is missing. MEMORY INFORMATION WARNING: Memory has been reconfigured due to a physical change or because the Page Deallocation Table (PDT) was cleared. This is for information only. No action is required. MEMORY STATUS TABLE Slot Size(a+b) Status ------------------0a/ b 64MB Configured 1a/b ??MB SIMM not seated properly. 2a/b 128MB Configured --------TOTAL 192MB DETAILED MEMORY CONFIGURATION TABLE SPA GROUP SMC SMC Status Bank Bank Status Size S

Use of other cables can result in significant problems with system operation. The narrow, singled-ended SCSI implemented on C160/C180/C200/C240/ C360 workstations limits the total cable length of narrow SE SCSI cables to 6 meters (19.6 feet). The fast, wide, differential SCSI definition limits the total cable length of FW SCSI cables to 25 meters (82 feet). The ultra, wide single-ended SCSI definition limits the total cable length of ultra, wide-SE SCSI cables to 3 meters (9.84 feet). Always use

To prevent such damage from occurring, observe the following precautions during board unpacking and installation: • Stand on a static-free mat. • Wear a static strap to ensure that any accumulated electrostatic charge is discharged from your body to ground. • Connect all equipment together, including the static-free mat, static strap, routing nodes, and peripheral units. • Keep uninstalled printed circuit boards in their protective antistatic bags. • Handle printed circuit boards by their edges,