Votes - 4, Average rating: 4.5
(
)
)
|
Other manuals for this model:
manual abstract
The monitor makes a sound when it is turned on. This is normal as some sound may be generated when the metal case and the electromagnet, which are installed to block any electromagnetic waves, interact with each other. How can I clean the outer case/Picture tube? Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning solution or plain water. Do not leave any remains of the detergent nor scratch the case. Do not allow any water to go inside the monitor. Self-Test Feature Check SyncMaster 591S/793S/793DF/795DF/797DF/793MB/795MB Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor. If your monitor works normally, the following screen appears. SyncMaster 591S/793DF/795DF SyncMaster 997DF Failure of any of the boxes to appear indicates a problem with your monitor. This box also appears during normal operation if the video cable becomes disconnected or damaged. 4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor. If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly. If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable. SyncMaster 591S/793DF/795DF SyncMaster 997DF The location and the position of the monitor may influence the quality and otherfeatures of the monitor. 1. If there are any woofer speakers near the monitor, unplug and relocate the woofer to another room. 2. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor. 3. Run the despeckling function again after moving your device. Self-Test Feature Check • A monitor recreates visual signals received from the PC. Therefore, if there is trouble with the PC or the video card, this can cause the monitor to become blank, have poor coloring, noise, Sync. Out of Range, etc. In this case, first check the source of the problem, and then contact a service center or your dealer. • Judging the monitor's working condition If there is no image on the screen or an "Sync. Out of Range" message comes up, disconnect the cable from the computer while the monitor is still powered on. • If there is a message coming up on the screen or if the screen goes white, this means the monitor is in working condition. • In this case, check the computer for trouble. Model Name SyncMaster 797DF General PowerSaver Preset Timing Modes General Picture Tube Type 17"(43cm) DynaFlat (40.6cm viewable) Deflection angle 90 ° Dot Pitch 0.20mm (Horizontal) Screen type Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask. Multi-layer coated with anti-static. Maximum Resolution 1600 x 1200@76Hz Active Display Horizontal 312 ± 4 mm Vertical 234 ± 4 mm Synchronization Horizontal 30 ~ 96 kHz Vertical 50 ~ 160 Hz Input Signal Definition Video Signal RGB, Analog 0.7 Vpp positive at 75 ohms Sync Signal Separate H/V sync, TTL level, positive or negative Display Color Unlimited Maximum Pixel Clock 250 MHz Power Supply 90 ~ 264VAC rms, 60/50 Hz ± 3Hz Power Consumption Less than 90W Dimensions (WxDxH) 401 x 410 x 378mm (After installation of Stand) Weight 14.3kg Environmental considerations Operating Temperature 32°F ~ 104°F(0°C ~ 40°C) Humidity 10% ~ 80%, non-condensing Storage Temperature -4°F ~113°F (-20°C ~ 45°C) Humidity 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Note: Design and specifications are subject to change without prior notice. This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF General when it is not needed, or when leaving it unatte...
Other models in this manual:Displays - 591S (2.54 mb)
Displays - 591V (2.54 mb)
Displays - 59E (2.54 mb)
Displays - 793DF (2.54 mb)