The "T.INFO" indicator disappears. 9-EN RDS Operation F SETUP Priority News This function allows you to preset to give priority to the News programme.You will never miss the News programme as the unit automatically gives priority to the News programme whenever it begins broadcasting, and interrupts the programme you are currently listening. This feature is functional when your unit is set to a mode other than the LW and MW modes. 1 Press the "F" button. The function indicator at the top side of

Tokyo office: 1-1-8 Nishi Gotanda, Shinagawa-ku, Tokyo 141-8501, Japan Tel.: (03) 3494-1101 ALPINE ELECTRONICS OF AMERICA, INC. 19145 Gramercy Place, Torrance, California 90501, U.S.A. Tel.: 1-800-ALPINE-1 (1-800-257-4631) ALPINE ELECTRONICS OF CANADA, INC. Suite 203, 7300 Warden Ave. Markham, Ontario L3R 9Z6, Canada Tel.: 1-800-ALPINE-1 (1-800-257-4631) ALPINE ELECTRONICS FRANCE S.A.R.L. (RCS PONTOISE B 338 101 280) 98, Rue De La Belle Etoile, Z.I. Paris Nord Il B.P. 50016 F-95945, Roissy, Char

band. 1 Press and hold the D.A.P. button for at least 2 seconds until the D.A.P. indicator appears. Press the BAND button to select FM or AM. The selected band will be displayed. To memorize stations onto the D.A.P. band, follow the steps for the automatic or Manual Storing of Station Presets section above. NOTE When using the Automatic Memory function with D.A.P., the first 3 presets will be filled with FM stations and the last 3 are filled with AM stations. To cancel the D.A.P. mode, press and

ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE. Route the cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent crimping and damage to the wiring. If wiring passes through a hole in metal, use a rubber grommet to prevent the wire’s insulation from being cut by the metal edge of the hole. HALT USE IMMEDIATELY IF A PROBLEM APPEARS. Failure to do so may cause personal injury or damage to the product. Return it to your a

Align the groove on the front panel with the projection on the main unit. 2 Push the left side of the front panel until it locks firmly into the main unit. 211 Immediately after installing or applying power to the unit, it should be initialized. 1 Press the POWER button to turn off the power. 2 Press the (Release) button to remove the front panel. 3 Using a ballpoint pen or other pointed object, press the RESET switch mounted behind this hole to complete the initialization procedure. RESET Switc

If the unit is still not functioning normally, please review the items in the following checklist. This guide will help you isolate the problem if the unit is at fault. Otherwise, make sure the rest of your system is properly connected or consult your authorized Alpine dealer. Basic No function or display. • Vehicle's ignition is off. -If connected following instructions, the unit will not operate with the vehicle's ignition off. • Improper power lead connections. -Check power lead connections.

• BEDIENUNGSANLEITUNG Lesen Sie diese Bedienungsanleitung bitte vor Gebrauch des Gerates. • MODE D'EMPLOI Veuillez lire avant d'utiliser cet appareil. • MANUAL DE OPERACION Lealo antes de utilizar este equipo. • ISTRUZIONI PER L'USO Si prega di leggere prima di utilizzare il attrezzatura. • ANVANDARHANDLEDNING Innan du anvander utrustningen bor du lasa igenom denna anvandarhandledning. ALPINE ELECTRONICS, INC. Tokyo office: 1-1-8 Nishi Gotanda, Shinagawa-ku, Tokyo 141-8501, Japan Tel.: (03) 3494

• Es posible que la longitud de la antena no sea adecuada. – Compruebe si la antena esta completamente desplegada. Si esta rota, reemplacela por otra nueva. In Case English Broadcast is noisy. • The antenna is not the proper – Extend the antenna fully; replace if it is broken. • The antenna is poorly grounded. – Make sure the antenna is grounded properly at its mounting location. En cas de Francais Reception parasitee. · La longueur de l'antenne ne – Deployez completement l'antenne, remplacez-la