Disposal of Old Disposal of waste Electrical & Electronic batteries (applicable Equipment in the European Union (Applicable in the and other European European
Please take the time to read this manual in its entirety to fully acquaint yourselfwith this cassette deck. Thankyou. Nakamichi Corporation. RISKOF ELEITRIT 5HIItK. DO TIOTOPEN I I AA CAUTION TO REDUCE THE RISK OF ELECTRICSHOCK,DO NOT REMOVECOVER(ORBACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICEPERSONNEL. Connections Afterconsultingthe instructions for your amplifieror receiver, use the shielded cables with RCA plugs (providedwith the deck) to make connections as sh
NOTE) Be sure that the lead wire does not come to contact with the heat exchanger. Fixing screw Wiring holding bracket Holding metal fitting for fan motor lead wire Concave part of ceiling panel Fan motor lead wire 104 No. Part name Procedure Remarks 11 Drain pan 1. Detachment 1) Perform works of procedure 4 -1 and 8 -1. 2) Remove the drain cap and extract drain water accumulated in the drain pan. NOTE) When removing the drain cap, be sure to receive drain water with a bucket, etc. 3) Take off s
• Check refrigerant stagnation in compressor. • Check MG-SW or OCR. Temperature change of TK2 could not be detected though compressor 2 started the operation. • Check TK2 sensor coming-off. • Check characteristics of TK2 sensor resistance value. • Check TK1, TK2, TK3, and TK4 misconnection. • Check SV3E valve operation. • Check capillary clogging of oil equalization circuit and check stop valve operation. • Check refrigerant stagnation in compressor shell. • Check MG-SW or OCR. Temperature chang
• Check cabling of current detection circuit system. • Check outdoor P. C. board (IPDU) error. H04 H04 — I/F Compressor 1 case thermo operation All stop Compressor 1 case thermostat performed protective operation. • Check compressor 1 case thermo circuit. (Connector, cable, P. C. board) • Check full opening of service valve. (Gas and liquid side) • Check outdoor PMV clogging. (PMV1, 2, 3) • Check SV41 circuit leakage. • Check miscabling/misinstallation of SV41 and SV42. • Check valve open status
• Check the power supply of indoor unit. (Power-ON) • Check connection of communication line between indoor and outdoor. • Check connector connection for communication in indoor P. C. board. • Check connector connection for communication in outdoor P. C. board. • Check indoor P. C. board failure. • Check outdoor P. C. board (I/F) failure. — E07 — I/F Indoor/outdoor communication circuit error (Detected at outdoor side) All stop Transmission from outdoor to indoor cannot continue for 30 seconds.
Internal format conversion function By installing an optional HKSR-5001, when the operation mode of this unit is 23.98PsF or 24PsF, a 59.94i or 60i mode HD SDI output (audio/VITC multiplex) is made available. Additionally, conversion in either direction between 1080.1920 and 720.1280, and conversion from 4:2:2 signal to 4:4:4 signal is possible, and with the additional installation of an HKSR-5003, conversion from a 4:4:4 signal to a 4:2:2 signal. Noiseless playback with DT heads When using the
It meets FCC requirements and complies with safety performance standards of the U. S. Department of Health and Human Services. Warnings: This CD player employs a laser light beam. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury. The use of controls, adjustments, or procedures other than those specified herein might result in hazardous radiation exposure. Note: Most material on compact discs and prerecorded tapes is copyrig
Можно согласовать до 9 устройств. (В зависимости от устройства, может потребоваться ввести код связи для каждого подключения.) Иногда согласование позволяет автоматически выполнить подключение. Для использования устройства после согласования запустите процедуру подключения. После установления соединения можно разговаривать с использованием громкой связи и слушать музыку. 1Расположите Bluetooth-устройство на расстоянии не более 1 м от данного устройства. 2Нажмите и удерживайте кнопку (BT), пока н