NOte: on a 4000 or 5000 series chartplotter, your service package appears on the system information screen (Configure > System > System Information > Weather Subscription) XM Radio: Highlight the Audio sub tab and verify that channels 7, 9, 47, and 122 are being received (see page 22). This indicates that all channels on XM’s basic radio service are being received. If within an hour the XM WX Weather and/or the XM Radio service has not activated, call XM customer care at 800-985-9200 to refresh

Tighten the RJ-45 locking ring clockwise until it is firmly sealed. Note: If you are using a Garmin GPSMAP 4000 or 5000 series chartplotter, you may not need a GMS 10 network port expander. The GPSMAP 4000 and 5000 series chartplotters have multiple RJ-45 sockets. Stand-alone Network Garmin radome GPS 17/17X Garmin Chartplotter NOTE : When using the Garmin radome with a stand-alone network, the chartplotter and GPS antenna (GPS 17) must be installed according to their installation instructions.

B Printed in Taiwan Thru-Hull Intelliducer Installation Instructions To obtain the best possible performance, install your Thru-Hull Intelliducer according to the following instructions. If you experience difficulty during the installation, contact Garmin Product Support, or seek the advice of a professional installer. The Intelliducer is designed for metal and fiberglass boats. Do not install this Intelliducer in a wood-hull boat. This Thru-Hull Intelliducer provides depth information either to

1. To customize system options on the GMI 10, from the instrument screen, select Menu > Setup > System. 2. For the listed options, select the appropriate settings or enter the necessary values. For example, you can select units of measure, language, enter total fuel capacity, and so on. To set the reference used to calculate heading information: 1. From the instrument screen, select Menu > Setup > System > Heading. 2. Choose from the following options: • Auto Magnetic—Automatic Magnetic Variatio

Before you begin the installation: • Read these instructions thoroughly. • Gather the appropriate fasteners and tools. • Verify that all cables can reach the radio mounting location. • Wear safety goggles and a dust mask when drilling, cutting, or sanding. Product Registration Help us better support you by completing our online registration today. Go to Keep the original sales receipt, or a photocopy, in a safe place. Contact Garmin Contact Garmin Product Support if you have any questions while

82A 157.125 157.125 Intership and Ship/Shore: Canadian Coast Guard use only in the St. Lawrence River/Great Lakes areas. 83 157.175 161.775 PC Ship/Shore and Safety: Canadian Coast Guard use only. 83A 157.175 157.175 EC Intership and Ship/Shore: Canadian Coast Guard and other Government agencies. 83B -161.775 AC, GL Safety: Continuous Marine Broadcast (CMB) Service. 84 157.225 161.825 PC Ship/Shore and Public Correspondence 85 157.275 161.875 AC, GL, NL Ship/Shore and Public Correspondence 86 15

3. Drill four 1/8 in. (3 mm) pilot holes.* 4. Mount the transceiver box using the included M4.2.25 screws. You can also use bolts, washers, and nuts (not included) to mount the transceiver box if the mounting surface allows. Connecting the Transceiver Box to Power Use the VHF 300 power/data cable to connect the transceiver box to a 12 Vdc battery through an external switch. Notes: • Use the VHF 300 Power Wiring-Assignment Table to identify the positive and negative wires. • The replacement fuse

Designated DSC Distress Call 1. Lift the spring-loaded door, and then press and release the DISTRESS key. 2. Use the Channel knob to select the type of distress call. 3. Press and hold the DISTRESS key for at least three seconds. Scanning Priority Channels 1. Press the 16/9 key (North American models) or the 16+ key (International models) to switch to Channel 16. 2. Press the 16/9 key or the 16+ key again to switch to the second-priority channel. 3. Press the 16/9 key or the 16+ key a third time

Professional installation of the autopilot system is highly recommended. Specific training in hydraulic pipe-fitting and in marine electrical connections is required to properly install the autopilot system. Read all installation instructions before proceeding with the installation. If you experience difficulty during the installation, contact Garmin Product Support. note: If your boat uses a Mercury® Verado® engine, you must also purchase a Mercury Verado Adapter Kit (Garmin part number 010-112

The GMI 10 will communicate with NMEA 2000- or NMEA 0183-compatible sensors and devices, and can show information such as speed, heading, water depth, and fuel information when connected to the appropriate sensors. Product Registration Help us better support you by completing our online registration today. Go to Keep the original sales receipt, or a photocopy, in a safe place. For future reference, write down the serial number assigned to your GMI 10 in the space provided below. The serial numbe