Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
Use the CANet Extension Cable or 22 AWG, 4-conductor shielded cable for data connections and 18 AWG for power. Transducer cable extensions are available through your Garmin dealer. WARNING: Do not connect or disconnect the transducer while the MFD and GSD 21 are connected and turned on . Doing so might damage the GSD 21. GSD 21 Sonar Module GSD 21 Sonar Module 3 INSTALLATION INSTRUCTIONS CANet Wiring for the Garmin GSD 21 Notes: 1. Power and ground wires require 18 AWG. You can extend the CANet wiring of the GSD 21 power/data cable up to 80 ft (24.38 m) total length using the CANet Connections Kit. 2. The CANet Extension Cable can support a maximum of two display units and one sonar unit. 3. The maximum length of cable from the CANet Extension Cable to the sonar or display units is 6 ft. 4. Refer to the chartplotter’s installation instructions for wiring the GPS 17 sensor and other devices. 5. Ground the drain wire at the first display unit. Do not ground the drain wire on the subsequent display units or sonar unit. 6. The CANet Extension Cable Black wire is reserved for future use. When inserting a CANet unit on the CANet Extension Cable, reconnect all wires according to their color. 7. When crimping the 3-wire connector, use a standard pair of pliers and make sure the button is fully depressed into the connector. .. GARMIN GSD 21 SOUNDER MODULE BLACK ORANGE GREEN WHITE CANet Terminator CANet Terminator CANet Extension Cable RED BLACK FUSE 2A TO BLACK TRANSDUCER DRAIN ORANGE GREEN WHITE BATTERY 10-35 VOLTS DC See the CANet Terminator Connection Diagram Below CANet Unit CANet Unit CANet Unit The CANet Extension Cable can be cut to any length 1 ft to 80 ft and a CANet compatible device can be inserted on the cable at any point between the two CANet Terminators. CANet CANet Multiple CANet Unit Connection CANet Terminator Connection CANet Terminator Green White Green 3 wire connector 3 wire connector Green White White To Sounder To Chartplotter Serial W iring for the Garmin GSD 21 to a Single GPSMAP 3005C/320 5 INSTALLATION INSTRUCTIONS Notes: You can extend the serial/power wiring of the 1. 22 AWG, 4-conductor shielded cable for data AWG for power. Ground the drain wire at the display 2. Refer to the chartplotter’s specifi c Installation Instructions for 3. When crimping the 3-wire use a standard pair of pliers 4. GSD 21 Sonar Module Serial Wiring for the Garmin GSD 21 to a Single GPSMAP 2006/2006C/2010/2010C/2106/2110/2206/2210/3006C/3010C/3206/3210 FUSE WIRE WIREGARMIN GSD 21 COLOR SOUNDER MODULE FUSE 3A 2A REDRED BLACKORANGE WHITE/BLUE BLACK WHITE/BLUEWHITE/BROWN WHITE/BROWN ORANGE TO TRANSDUCER BATTERY10-33 VOLTS DC Notes: You can extend the serial/power wiring of the GSD 1. 22 AWG, 4-conductor shielded cable for data connections AWG for power. Ground the drain wire at the display unit. 2. Refer to the chartplotter’s specifi c Installation Instructions for wiring 3. When crimping the 3-wire connector, use a standard pair of pliers and 4. INSTALLATION INSTRUCTIONS GSD 21 Sonar Module Serial Wiring for the Garmin GSD 21 to a Single GPSMAP 276C/296/376C/396 INSTALLATION INSTRUCTIONS Notes: You can extend the serial/power wiring of the GSD 21 power/1. Extension Cable or 22 AWG, 4-conductor shielded cable for data connections AWG for power. Ground the drain wire at the display unit. Do not 2. The Orange wire must be pulled low (-) in 3. Option 1: If the GSD 21 is wired to a circuit The GSD 21 and the GPSMAP 276C/296/376C/396 turn on or off when power is applied or removed Option 2: If the Red (+) wire is The GSD 21 turns on or off when ground is applied or When crimping the 3-wire use a standard pair of 4. connector. GSD 21 Sonar Module Serial Wiring for the Garmin GSD 21 to a Single GPSMAP 182/182C/192C/232/292/392/492 WIREWIRE GARMIN GSD 21 COLOR COLOR FUSEFUSESOUNDER MODULE 3A 2A REDRED BLACKORANGE WHITE/BLUE BLACK BLUEBROWN WHITE/BROWN ONOFF SEE NOTE 3OPTION 1ON OFF SEE NOTE 3OPTION 2 TO TRANSDUCER BATTERY10-33 VOLTS DC Notes: You can extend the serial/power wiring of the GSD 21 power/1. Cable or 22 AWG, 4-conductor shielded cable for data connections AWG for power. Ground the drain wire at the display unit. Do not 2. The Orange wire must be pulled low (-) in 3. Option 1: If the GSD 21 is wired to a The GSD 21 and the GPSMAP 182/182C/192C/232/292/392/492 when power is applied or removed Option 2: If the Red (+) wire is The GSD 21 turns on or off when ground is applied or When crimping the 3-use a standard pair of 4. INSTALLATION INSTRUCTIONS GSD 21 Sonar Module Serial Wiring for the Garmin GSD 21 to a Single GPSMAP 172/172C INSTALLATION INSTRUCTIONS Notes: You can extend the serial/power wiring of the GSD 1. 22 AWG, 4-conductor shielded cable for data connections AWG for power. Ground the drain wire at the display unit. 2. Refer to the3. GPSMAP 172/172C Owner’s Manual for wiring the GPS 17 sensor and When crimping the 3-wire connector, use a standard pair of pliers 4. INSTALLATION INSTRUCTIONS Blink Codes ...