(6.2kg) 120VAC, 50/60Hz, 840 Watts I3I/2” (34.3cm) 1/16” (2mm) 1.5 mil up to 10 mil (37 micron - 250 micron) each side WARRANTY AND RETURN POLICY Warranty: Your laminator is warranted to be free of defects in materials and workmanship for a period of one year from the date of purchase. In the event of a defect in material or workmanship, your dealer will (at his/her option) repair or replace the laminator. No other warranty is implied except as stated above. This warranty does not cover da

1 Introduction Congratulations on the purchase of your new CHAU VET lighting effect. We are confident you will enjoy many trouble free hours with this unit. To assist with the care and use of the product we have prepared this short guide. Operation This lighting effect has been designed to function on a mains power supply of either 120V~60Hz or 230V~50Hz and has been fitted with a suitable power plug for use with your local voltage. Check the label on the unit and the power plug for the corr

Power Light 2. Foam Board/Pouch Selector 3. On/Off Switch 4. Ready Light 5. Temperature Control 6. Loading Area Safety Instructions 1. Read all instructions before use. Save these instructions for later use. 2. Follow all warnings and instructions marked on the product. 3. Use the Fellowes laminator only for its intended purpose of laminating documents according to the indicated specifications. 4. Extreme caution should be taken when the appliance is used by or near children or invalids. 5. Do n

while ffrmiy puiiinq ism out the rea^ of îne ¡am:nator Ciontmue pi;* .iH'j the Mrr u.nt-i : ijfVA.nor>completely from the rotie's At ihis point you w^i iee ^ rnorr.^ni^'y lightening o* tension, to* owed r;y a si-o^g i>-:i m the opposite ejection 3 Release the reverse swuch. an^ r.jn tnt1- ia^ nator forward cntil ai* wnnk.ed filrr* exit^out t*v- rear NOTE: If film is wrapped arourvj the pultrolier!, does not extend out the rear of the larnnatof re^vicw the top iiim supply roll, and pofi the

Punching/Crimping Handle 2. Punching Area 3. Adjustable Margin Guide 4. Wire Size Selector 5. Paper Support 6. Binding Support 7. Crimping Area 8. Crimping Area Adjustor Dial 9. Waste Paper Tray 10. Crimping Area Size Indicator 5 13 7 4810 9 6 2 Assembly To assemble your WB 100 Wire Binding Machine, simply attach the Punching Handle to the right side of the machine and secure with the screw supplied. Next, attach Paper Support in Crimping Area as show in the diagram. Using the Binding Machine Pu

On\Off Switch 2. Ready Light 3. Binding Area 4. Cooling Stand 5. Binding Timer (TB 200 only) 4 1 2 3 4 5 13 Using the Binding Machine 1. Turn On\Off switch to "On" position. 2. Machine is ready to bind when Ready Light illuminates (approximately 1-2 minutes). 3. Using the table below, choose the correct thermal cover based on the total number of sheets to be bound: Thermal Cover Size # of Sheets Inches mm 1-30 1\8" 3.2 31-60 1\4" 6 61-90 3\8" 9.5 91-120 1\2" 12.5 121-150 5\8" 15.5 151-180 3\4" 2

The base incorporates key hole slots for wall mounting. The switches use the most recent technology features like Auto MDI/ MDI- X function on all ports and non blocking architecture. Features • Ethernet IEEE 802.3 ( 10Base- T) & Fast Ethernet 802.3u ( 100Base- TX) compliant • 10/ 100Mbit/ sec, Full or Half- Duplex, Auto- Negotiation on all ports • Store & Forward architecture • Forwarding/ Filtering Rate 148,800 packets / sec. • MAC address table: 1K, Buffer 128KByte • Status LEDs for Power, 10

If not either the power supply or the switch ( or LED) might be faulty. Contact your dealer in this case. • If you connect any powered device to a port the LINK/ Activity LED of this port should light. If not use another patch cable and check that the device you have connected is powered on and it’s network port is active. • Make sure all network and patch cables are STP or UTP and are not broken. Make sure any distance between the Switch and a device is 100m or less. Deutsches Benutzerhandbuch

Sheet Supporter/Adjustable Coil Guide Selector 3. Adjustable Paper Margin Guide 4. Punching Area 5. Waste Paper Drawer 6. Binding Tray 7. Margin Depth Selector 8. Left Side Cover 9. Punching Handle Cover 1 4 8 3 7 6 2 9 5 Assembly 1. Attach the Punching Handle to the right side of the machine by firmly pressing square hole of handle onto square shaft. To operate correctly, the handle should be positioned as illustrated above. NOTE: If the handle is not positioned as illustrated it will not punch