If you use this tool unsafely or incorrectly, you can suffer serious personal injury. 1. Hold tool by insulated gripping surfaces 4. Check the bit carefully for cracks or dam- when performing an operation where the age before operation. Replace cracked or cutting tool may contact hidden wiring or damaged bit immediately. its own cord. Contact with a “live” wire will 5. Avoid cutting nails. Inspect for and make exposed metal parts of the tool “live” remove all nails from the workpiece and shock t

Do not force it past 5 or 1, or the speed adjusting function may no longer work. CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 003670 Installing or removing the bit CAUTION: • Install the bit securely. Always use only the wrench provided with the tool. A loose or overtightened bit can be dangerous. • Do not tighten the collet nut without inserting a bit or install small shank bits without using a collet sleeve. Either can lead to

Minute depth adjustments can be obtained by turning the stopper pole (1.5 mm or about 1/16” per turn). Now, your predetermined depth of cut can be obtained by loosening the lock lever and then lowering the tool body until the stopper pole makes contact with the adjusting hex bolt. By turning the knob, the upper limit of the tool body can be adjusted. When the tip of the bit is retracted more than required in relation to the base plate surface, turn the knob to lower the upper limit. CAUTION: • S

Replace cracked or damaged bit immediately. 3.Avoid cutting nails. Inspect for and remove all nails from the workpiece be- fore operation. 4. Hold the tool firmly with both hands. 5. Keep hands away from rotating parts. 6. Make sure the bit is not contacting the workpiece before the switch is turned on. 7. Before using the tool on an actual workpiece, let it run for a while. Watch for vibration or wobbling that could indicate improperly installed bit. 8. Be careful of the bit rotating direction

The stopper block is also convenient for making three passes with progressively deeper bit settings when cutting deep grooves. CAUTION: • When using a bit having total length of 60 mm (2 - 3/8”) or more, or edge length of 35 mm (1 - 3/8”) or more, the depth of cut cannot be adjusted as previously mentioned. To adjust, proceed as follows: Loosen the lock lever and carefully adjust bit protrusion below the tool base to the desired depth of cut by moving the tool body up or down. Then re-tighten th

Replace cracked or cutting tool may contact hidden wiring or damaged bit immediately. its own cord. Contact with a “live” wire will 5. Avoid cutting nails. Inspect for and make exposed metal parts of the tool “live” remove all nails from the workpiece and shock the operator. before operation. 2. Wear hearing protection during extended 6. Hold the tool firmly. period of operation. 7. Keep hands away from rotating parts. 3. Handle the bits very carefully. 8. Make sure the bit is not contacting the

Moving the tool forward too slowly may burn and mar the cut. The proper feed rate will depend on the bit size, the kind of workpiece and depth of cut. Before beginning the cut on the actual workpiece, it is advisable to make a sample cut on a piece of scrap lumber. This will show exactly how the cut will look as well as enable you to check dimensions. CAUTION: • Since excessive cutting may cause overload of the motor or difficulty in controlling the tool, the depth of cut should not be more than

After adjusting, tighten the clamping nut firmly to secure the tool base. Adjusting angle of tool base 006632 5 1. Wing bolt 1 2. Graduation 2 3. Wing nut 6 4. Trimmer shoe 3 5. Amount of chamfering 6. Base 4 Loosen the wing bolts and adjust the angle of the tool base (5° per graduation) to obtain the desired cutting angle. Adjusting amount of chamfering To adjust the amount of chamfering, loosen the wing nuts and adjust the trimmer shoe. CAUTION: • With the tool unplugged and switch in the “OFF