Votes - 2, Average rating: 4
(
)
)
|
manual abstract
After adjusting, tighten the clamping nut firmly to secure the tool base. Adjusting angle of tool base 006632 5 1. Wing bolt 1 2. Graduation 2 3. Wing nut 6 4. Trimmer shoe 3 5. Amount of chamfering 6. Base 4 Loosen the wing bolts and adjust the angle of the tool base (5° per graduation) to obtain the desired cutting angle. Adjusting amount of chamfering To adjust the amount of chamfering, loosen the wing nuts and adjust the trimmer shoe. CAUTION: • With the tool unplugged and switch in the “OFF” position, rotate the collet nut on the tool several times to be sure that the bit turns freely and does not contact the base or trimmer shoe in any way. Switch action 006614 1. Switch lever 1 To start the tool, move the switch lever to the I (ON) position. To stop the tool, move the switch lever to the O (OFF) position. 4 ASSEMBLY ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Installing or removing trimmer bit 006629 1 2 3 1. Loosen 2. Tighten 3. Hold CAUTION: • Do not tighten the collet nut without inserting a bit, or the collet cone will break. • Use only the wrenches provided with the tool. Insert the bit all the way into the collet cone and tighten the collet nut securely with the two wrenches. To remove the bit, follow the installation procedure in reverse. Installing trimmer shoe (after it has been removed from the tool) 006630 1 2 3 4 5 6 1. Wing nut 2. Spring washer 3. Base 4. Trimmer shoe 5. Flat washer 6. Bolt NOTE: • The trimmer shoe is factory installed on the tool. Use the bolts, wing nuts, spring washers and flat washers to install the trimmer shoe as shown in the figure. OPERATION 006633 2 1 1. Trimmer shoe 2. Base Turn the tool on without the bit making any contact with the workpiece and wait until the bit attains full speed. Then move the tool over the workpiece surface, keeping the tool base and trimmer shoe flush with the sides of the workpiece. NOTE: • This tool can be used as a conventional trimmer when you remove the trimmer shoe. When doing edge cutting, the workpiece surface should be on the left side of the bit in the feed direction. 2 44 1 2 3 1. Workpiece 2. Bit revolving direction 3. View from the top of the 4. Feed direction tool NOTE: • Moving the tool forward too fast may cause a poor quality of cut, or damage to the bit or motor. Moving the tool forward too slowly may burn and mar the cut. The proper feed rate will depend on the bit size, the kind of workpiece and depth of cut. Before beginning the cut on the actual workpiece, it is advisable to make a sample cut on a piece of scrap lumber. This will show exactly how the cut will look as well as enable you to check dimensions. • When using the trimmer shoe, the straight guide or the trimmer guide, be sure to keep it on the right side in the feed direction. This will help to keep it flush with the side of the workpiece. 001985 1 2 3 4 1. Feed direction 2. Bit revolving direction 3. Workpiece 4. Straight guide CAUTION: • Since excessive cutting may cause overload of the motor or difficulty in controlling the tool, the depth of cut should not be more than 3 mm (1/8”) at a pass when cutting grooves. When you wish to cut grooves more than 3 mm (1/8”) deep, make several passes with progressively deeper bit settings. 5 6 Templet guide The templet guide provides a sleeve through which the bit passes, allowing use of the trimmer with templet patterns. Remove the tool base from the tool. Loosen the wing bolts and secure the tool base horizontally. Loosen the two screws on the tool base. Place the templet guide on the tool base. There are four convex portions on the templet guide. Secure two of the four convex portions using the two screws. Install the tool base on the tool. Secure the templet to the workpiece. Place the tool on the templet and move the tool with the templet guide sliding along the side of the templet. NOTE: • The workpiece will be cut a slightly different size from the templet. Allow for the distance (X) between the router bit and the outside of the templet guide. The distance (X) can be calculated by using the following equation: Distance (X) = (outside diameter of the templet guide - router bit diameter) / 2 Straight guide (optional accessory) Attach the guide plate to the straight guide with the bolt and the wing nut. 1. Screws 2. Wing bolt 3. Base 4. Screwdriver 1. Template guide 2. Base 3. Convex portions 1. Straight bit 2. Base 3. Templet 4. Distance (X) 5. Workpiece 6. Templet guide 10 006639 1 2 3 4 006640 1 2 3 006641 1 2 3 4 5 6 10mm(3/8”) 001988 1. Bolt 2. Guide plate 3. Straight guide 4. Wing nut 1. Clamp screw (A) 2. Straight guide 3. Wing nut 4. Base 5. Wing bolt 006634 1 2 3 4 006617 1 2 3 4 5 006635 A 006636 Circular wor k Trimmer guide 1 4 5 006619 1. Wing nut 2. Guide plate 3. Straight guide 4. Center hole 5. Bolt 2 3 Circular work may be accomplished if you assemble the straight guide and guide plate as shown in the figures. Min. and ...