Votes - 1, Average rating: 4
(
)
)
|
manual abstract
Use only U.L. and CSA listed extension cables. Never use two extension cables together. Instead, use one long one. Total Extension Cord Lenght (feed) 25 50 100 150 Cord size (AWG) 18 16 16 14 Note: • The lower the AWG number, the stronger the cable. Switching the ma chine on and off Keep the machine steady during switching and during use by holding the handles [3-1] [3-2] with both hands. The switch [3-4] is an on/off switch (I = ON, 0 = OFF). 3-1 3-3 3-2 3-4 Tool settings Disconnect the plug from the cool down for approx. 3-5 minutes before using it again. The machine requires less time to cool down if it is running, i.e. in neutral position. Changing the router table The “large surface router table” is already fitted as standard. The large contact surface and precision adjustment features of this router table enable a high degree of accuracy. Other router tables are included in the accessories programme. a) Large surface router table 21 4-1 4-2 power source before making any adjustments, changing accessories, or storing power tools. Electronic control The machine features full-wave electronics with the following properties: Smooth start-up The electronically controlled smooth start-up function ensures that the machine starts up smoothly. Speed control You can regulate the rotational speed steplessly between 10000 and 26000 rpm using the adjusting wheel [3-3]. This enables you to optimise the cutting speed to suit the respective material. Constant speed The preselected motor speed remains constant through electronic control. This ensures a uniform cutting speed even when under strain. Temperature control To prevent overheating, the safety electronics switches the machine off when it reaches a critical motor temperature. Let the machine – Slide the router table onto the retaining pin [4-1] on the machine. – Tighten the screw [4-2] to clamp the router table in position. 4-5 4-4 4-3 543 – Place the extraction hood [4-4] in position. – Tighten the screw [4-3] to clamp the extraction hood in position. – Place the extractor connector [4-5] on the extraction hood. Removal is performed in reverse sequence to installation. 10 b) Router table for edge veneer The "router table for edge veneer" (only in SET scope of delivery) is designed for fl ush trimming veneer overhang and profi le routing. Notes: .. The router table is tilted 1.5° so that the surface coating is not damaged during edge routing. A router table with 0° inclination angle for precise cuts is available as an accessory. 5-1 5-2 1 2 – Secure the sensor [5-1] to the machine using the preassembled screws. Slide the sensor in the long holes to adjust the routing tool to the perfect position. – Slide the router table onto the retaining pin [5-2] on the machine. 5-3 5-4 3 4 – Tighten the screw [5-3] to clamp the router table in position. – Place the extraction hood [5-4] in position. 5 5-5 – Tighten the screw [5-5] to clamp the extraction hood in position. Removal is performed in reverse sequence to installation. Changing the routing tool Risk of accident - the routing tool may be hot after use and has sharp edges. Allow the tool to cool before changing. Wear protective gloves when changing tools. – Remove the router table before changing the routing tool. SW 19 6-2 6-3 6-1 2 1 3 a) Removing the tool – Press the spindle lock [6-1]. – Unscrew the locking nut [6-2] using the open-end wrench (size 19) until you are able to remove the tool. b) Inserting the tool – Insert the routing tool [6-3] into the open clamping collet as far as possible, but at least up to the mark ( ) on the shank. – Press the spindle lock [6-1]. – Tighten the locking nut [6-2] using the open-end wrench (size 19). Changing the clamping collet Only compatible tools can be used in combination with the clamping collets supplied. 8 mm, 6 mm and 1/4" (6.35 mm) clamping collets can be used. 7-2 7-3 7-1 1 2 3 – Press the spindle lock [7-1]. – Unscrew the locking nut [7-2] completely. – Remove the locking nut from the spindle together with the clamping collet [7-3]. Do not separate the locking nut and clamping collet as these form a single component. 11 – Attach a different clamping collet with locking nut to the spindle. – Screw on the locking nut loosely. Do not tighten the locking nut until a router bit is inserted. Adjusting the routing depth 8-2 8-3 8-1 1 1 3 3 2 8-2 8-3 1 3 2 – Unscrew the rotary knob [8-3] and the clamp [8-1] (“large surface router table” only). – Turn the rotary wheel [8-2] to set the router table to the required routing depth. – Tighten the rotary knob [8-3] and the clamp [8-1] (“large surface router table” only). Dust extraction Breathing in dust can damage the respiratory passage! Always connect the machine to a dust extractor. When performing work that generates dust, always wear a dust mask. Extraction hoods are supplied for both router tables; a Festool extractor (extractor hose with a diameter of 27 mm) can be connected to these extraction hoods. The dust extractor (...