Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
(Refer to page 8 for details.) If your amplifier does not have any line output terminal, connect the subwoofer to the speaker output terminals of the amplifier. (Refer to page 9 for details.) Center speaker Rear speakers SPEAKERS MAIN CENTER REAR (SURROUND) OUTPUT SUB WOOFER CAUTION SEE INSTRUCTION MANUAL FOR CORRECT SETTING. MAIN A B A B CENTER REAR (SURROUND) /MONO VOLUME INPUT1 FROM AMPLIFIER OUTPUT TO SPEAKERS INPUT2 AUTO STANDBY STANDBY-RED ON-GREEN OFF LOW HIGH OFF POWER ON 0 I0 INPUT2 /MONO REAR RREAR L REAR RCENTERREAR L CENTER FRONT R FRONT R FRONT L FRONT L Right Subwoofer To AC outlet Left Amplifier Right Left Main speakers EnglishEnglish . How to connect speaker cords to the input and output terminals of the speakers For connections, keep the speaker cords as short as possible. Do not bundle or roll up the excess part of the cords. If the connections are faulty, no sound will be heard from the speakers. Main/center/rear speakers One side of the provided speaker cord has a white broken line and the other side has no line. Connect the (+) terminals on both the speaker and the amplifier using the side with a white broken line. Connect the (–) terminals on both components using the side with no line. White broken line Red: positive (+) Black: negative (–) Subwoofer (INPUT1/OUTPUT terminals) Connect the (+) terminals on both the subwoofer and the amplifier using one side of the cord. Connect the (–) terminals on both components using the other side of the cord. Red: positive (+) Black: negative (–) How to Connect: 1 Press and hold the terminal’s tab, as shown in the figure. 2 Insert the bare wire end properly into the terminal hole. [Remove approx. 10 mm (3/8”) insulation from the speaker cord.] 10 mm 3 Release your finger from the tab to allow it to lock securely on the cord’s wire end. 4 Test the firmness of the connection by pulling lightly on the cord at the terminal. Note Do not let the bare speaker wires touch each other as this could damage the speaker or the amplifier, or both of them. E-7 Various ways of connecting the subwoofer . Connecting the subwoofer to line output (pin jack) terminals of the amplifier (The basic way) Connect the main speakers to the speaker output terminals of the amplifier. . To connect with a YAMAHA DSP amplifier (or AV . To connect the subwoofer to the SPLIT SUBWOOFER receiver), connect the SUBWOOFER (or LOW PASS etc.) terminals on the rear of the DSP amplifier, connect them terminal on the rear of the DSP amplifier (or AV receiver) to both the left L and right R INPUT2 terminals of the to the L/MONO INPUT2 terminal of the subwoofer. subwoofer. Subwoofer Amplifier Pin plug cord (included) To AC outlet /MONO VOLUME INPUT1 FROM AMPLIFIER OUTPUT TO SPEAKERS INPUT2 AUTO STANDBY STANDBY-RED ON-GREEN OFF LOW HIGH OFF POWER ON 0 I0 SPLIT SUBWOOFER SUBWOOFER (LOW PASS) INPUT2 /MONO Notes . Some amplifiers have line output terminals labeled PRE OUT. When you connect the subwoofer to the PRE OUT terminals of the amplifier, make sure that the amplifier has at least two sets of PRE OUT terminals. If the amplifier has only one set of PRE OUT terminals, do not connect the subwoofer to the PRE OUT terminals. Instead, connect the subwoofer to the speaker output terminals of the amplifier. (Refer to pages 6 and 7.) Pin plug cords (not included) . When connecting to a monaural line output terminal of the amplifier, connect the L/MONO INPUT2 terminal. . When connecting to line output terminals of the amplifier, other speakers should not be connected to the OUTPUT terminals on the rear panel of the subwoofer. If connected, they will not produce sound. English English . Connecting the subwoofer to speaker output terminals of the amplifier If your amplifier has only one set of main speaker output terminals Connect the speaker output terminals of the amplifier to the INPUT1 terminals of the subwoofer, and connect the OUTPUT terminals of the subwoofer to the main speakers. Left main Right main speaker speaker Subwoofer Amplifier Speaker output terminals To AC outlet /MONO VOLUME INPUT1 FROM AMPLIFIER OUTPUT TO SPEAKERS INPUT2 AUTO STANDBY STANDBY-RED ON-GREEN OFF LOW HIGH OFF POWER ON 0 I0 INPUT1 FROM AMPLIFIER OUTPUT TO SPEAKERS If your amplifier has two sets of speaker output terminals Subwoofer (Both A and B speaker outputs must be ON.) Amplifier Speaker output terminals To AC outlet /MONO VOLUME INPUT1 FROM AMPLIFIER OUTPUT TO SPEAKERS INPUT2 AUTO STANDBY STANDBY-RED ON-GREEN OFF LOW HIGH OFF POWER ON 0 I0 A B INPUT1 FROM AMPLIFIER OUTPUT TO SPEAKERS Left main speaker Right main speaker E-9 USING THE SUBWOOFER (SW-P201) USING THE SUBWOOFER (SW-P201) m Controls and their functions Rear panel INPUT1 FROM AMPLIFIER OUTPUT TO SPEAKERS INPUT2 /MONO AUTO STANDBY STANDBY-RED ON-GREEN OFF LOW HIGH OFF POWER ON1VOLUME 0 I0 OFF POWER ON 564INPUT1 FROM AMPLIFIER OUTPUT TO SPEAKERS INPUT2 /MONO AUTO STANDBY STANDBY-RED ON-GREEN OFF LOW HIGH VOLUME 0 I0 237VOLTAGE SELECTOR 220V-240V 110V-120V VOLTA...