Votes - 4, Average rating: 4
(
)
)
|
manual abstract
Before assembling, remove all traces of the packing grease from the Jointer and wipe all parts thoroughly with a clean dry cloth. When cleaning do not use acetone, gasoline or paint thinner as these solvents are dangerous to you and may also cause damage to plastic and rubber parts. Apply a thin coating of automotive wax to any unpainted surfaces to prevent rust. Caution!: Consider the weight of the components and take the necessary precautions when lifting. Assistance may be required during assembly. #31849 Page 4 The Stand The Stand Front Side Plate(16A) Rear Side Plate (30A) Upright Plate (4A) Motor (29A) Side Link Plate(19A) Crossbeam Plate (18A) Figure 1 Step 1) Attach the Front Side Plate (#16A) to both of the Side Link Plates (part #19A). Insert two Screws (#17A) through Front Side Plate and through Side Link Plate. Slide on Washers (#7A) and Nut (#6A). Tighten into place. Repeat for the other side - see Figure 1. Step 2) Attach the Rear Side Plate (#30A) to each of the Side Link Plates (#19A). Tighten it into place with two Screws (#17A) and attach Washers (#7A) and Nuts (#6A) on inside. Repeat for other side-see Figure 1. Step 3) Set the Crossbeam Plate (#18A) so that it sits on top of each of the Side Link Plates (#19A). Insert two (2) Screws (#17A) through the Crossbeam Plate (#18A) and Side Link Plate. Slide on Washers (#7A) and Nuts (#6A). Tighten into place. Repeat for other end of Crossbeam Plate- see Figure 1. Step 4) Set the Roof (#1A) on top of the Side Plates. Insert two Screws (#17A) at each corner. On the inside slide on Washer (#7A) and Nut (#6A). Secure in place-see Figure 1. Step 5) Attach the foot Bolt (#22A) through the Chassis (#20A) and to the bottom of each corner. From the top, slide on Washer (#7A) and tighten on Nut (#6A). Step 6) Set the Jointer on the Stand with the Cutterhead Guard facing the Front SidePlate (#16). There are two holes for the Bolts (#68-Jointer Assembly) over the Right Protecting Plate (#8A) and one hole for a Bolt (#68-Jointer Assembly) in the center of the Roof (#1A) above the Left Protecting Plate (#26A). Slide the Bolt (#68-Jointer Assembly) through the flat Washer (#67-Jointer Assembly) through the Roof (#1A) and into the Jointer. Step 7) Attach the Right Tapping Fender (#23A) and the Left Tapping Fender (#27A) to the Tapping Plate (#25A). Insert Lock Washer (#21A) with the head on the outside of the Stand. Slide on Washer (#7A) and Nut (#6A). Tighten Tapping Fenders onto Plate-see Figure 2. Step 8) Attach a Lock Plate (part #24A) to each corner hole and to the top hole in the Left Protecting Plate (#26A). Make certain that the part of the Lock Plate with the wing is on the outside of the Protecting Plate-see Figure 2. #31849 Page 5 Step 9) Attach the Tapping Plate (#25A) with Right and Left Tapping Fenders (#23A & #27A) to the Left Protecting Plate (#26A). Insert the Screws (#17A) with head on the outside of the Plate. On the inside, slide on Washer (#7A) and Nut (#6A)-see Figure 2. Step 10) Attach the Reinforcing Plate (#3A) to the Roof ( #1A) on the same side as the Left Protecting Plate using Screws (#17A), Washers (#7A) and Nuts (#6A). Step 11) Attach the Upper Link Plate (#2A) to the Roof (#1A) with Screw (#17A) inserted downward. Slide on Washer (#7A) and tighten on Nut (#6A)-see Figure 1. Step 12) Slide the Left Protecting Plate (#26A) on and tighten it into place with six (6) Screws (#17A). Fasten on the inside with Washers (#7A) and Nuts (#6A). Make certain that the lips at the top of the Tapping Plate (#25A) are positioned under the Upper Link Plate (#2A) as in Figure 1. Step 13) Attach the Motor (#29A) to the Upright Plate (#4A) making certain that the Screws (#17A) are placed at least half way up the Plate (#4) on the side opposite the lips. You will have to move the Motor (#29A) later when tensioning the Belt. Secure in position with Washer (#7A) and Nut (#6A)-see Figure 1. Step 14) Mount the Upright Plate (#4A) so that it is attached at the top to the Upper Link Plate (#2A) and at the bottom to the Side Link Plate (#19A). Attach to the Upper Link Plate making sure that the lips of the Tapping Plate (#25A) are sandwiched between the Upper Link Plate (#2A) and the Upright Plate (#4A). Step 15) Attach three (3) Lock Plates (#24A) to the Right Protecting Plate (#8A). Slide the Plate onto the Frame and twist the Lock Plates so that the Right Protecting Plate is securely in position. Jointer Assembly Each of the following part numbers, unless otherwise specified, are from the Jointer Parts List on page 14 and the Jointer Assembly Diagram on page16. Step 1) Attach the Belt Cover (#64) to the Stand (#69). Make certain that the Belt (#10) is in place on the Center Head Pulley (#9). Insert Recessed Screw (#63) through each foot of the Belt Cover (#64). From underneath, attach Lock Washer (#65) and tighten into place with Nut (#66). Adjusting Belt Tension Correct tension is indicated when there is approximately 1" deflection in the Belt (#10) with...