4. Consumer must pay charges for wiring and installation. 3 • SAFETY INSTRUCTIONS (CONTINUED) The receptacle should be an individual branch circuit used only for this air conditioner. Be sure the electrical service is adequate for the model air conditioner you have chosen. The complete electrical rating of your air conditioner is stated on the name plate located at the unit’s side. Be sure the plug receptacle is close enough for the power cord to reach it. WARNING : An extension cord should not
- c”~ ” D E “ 7-8^ 6- 0% 2-113/i6 0-11’/7 5^ FPT 7-3?] 6 6-11 2-5% 0-105/s V MPT 0-6 - L 1 o i "(|05> ' “ 1 6-9 8 (110 )—H 1 - 1 A 'l20> ^"E SIZE COOLER DRAIN L 1 i i" 1 — 7 -7 \ MTG HOLES-*\ -- 7-7-I"(085)-- 7'-7-g- MTG HOLES- 20-6 MTG HOLES - SIDE VIEW LEGEND for Fig. 1 (callouts) 1 — Electrical box, circuit 1 9 2 — Electrical box, circuit 2 10 3 — Unit control box 11 4 — Compressor (1 and 2, circuit 1; 3 and 4, circuit 2) 12 5 — Condenser coils 13 6 — Removable access pan
• Be sure to use an exclusive power source. • Contact service man for replacement of power cord. 4 • Step 1 - Prepare Components For Installation Parts for installation are as follows; • SCREW TYPE • Sill Bracket (2 pieces) • Window Kit Left side (Frame ‘L+Shutter) - (1 piece) • Window Kit Right side (Frame ‘R+Shutter) - (1 piece) • Sash Bracket (1 piece) • Frame Guide Lower - (2 pieces) • Levelling Screw (Machine M8x45) - (2 pieces) • 11/4 inch Screw (M5x30) - (4 pieces) • 5/8 inch Screw - (M4x
(Under this condition, the water pump is not activated.) 6 INSTALLATION Install the mobile ir conditioner in a flat and spacious location where the air outlets will not be covered up. A minimum clearance of 30cm from a wall or other obstacles should be kept. The appliance shall not be used in the laundry. The plug shall accessible after appliance is positioned. Wiring shall be done according to National rules. 1 IMPORTANT: 2 DUCT MOUNT INSTRUCTIONS: Exhaust Air Oulet Duck A) TEMPORARY- 1. Attach
The unit must then be set up by following the on-screen prompts before it can be used. To change the data that was entered during the initial set-up process, or to perform other functions such as clearing job history or recalibrating the pressure transducers, re-enter the System Set-Up mode as follows: 1. If not already done, plug the MAC2000 into a properly grounded AC outlet; set the Power switch to ON; then wait until the unit completes its self diagnostics. The screen will display “Select mo
3. Use drapes, curtains, or shades to keep direct sunlight from heating your room, but DO NOT obstruct the air conditioner. Allow air to circulate around the unit without obstructions. 4. Start your air conditioner before outdoor air becomes hot/cold and uncomfortable. This avoids an initial period of discomfort while the unit is cooling or heating off the room. 5. When outdoor temperature is cool enough, use HIGH or LOW FAN only. This circulates indoor air, providing some cooling comfort, and u
Keep unit as far away as possible from obstacles and obstructions and at least 30" above the floor or ground. Curtains and other objects within a room should be prevented from blocking the air flow. Window opening requirements (see table below) Awning Side obstruction Ground Fence, wall, or other obstacle. 12" Min. 30" Min. 20" Min. 20" Min. Fig.B ModelSize 8K-10K 12K 15-24K Cabinet size (W*H*D) 20.5" *14.8" *23.1" 22.8" *15.7" *24.1" 26.5" *18.5" *26.9" Min. Window opening 24" 27" 30" Max. Wind
IMPORTANT SAFETY INSTRUCTIONS WARNING:To reduce the risk of fire, electrical shock, or injury when using your air conditioner, follow these basic precautions: • Plug into a grounded 3-prong outlet. • Do not remove ground prong. • Do not use an adapter. • Do not use an extension cord. • Unplug air conditioning before servicing. • Use two or more people to move and install air conditioner. —SAVE THESE INSTRUCTIONS — 4 WAC 8-24 USER MAN FINAL 3/2/05 12:13 PM Page 7 INSTALLATION REQUIREMENTS • The a
They may be located in any area having unobstructed air circulation; the low silhouette permits installation in varied ground or roof locations. Each unit consists of a direct drive motor (or motors), fan (or fans), fan guards, motor mounts, condenser coil with integral subcooling circuit, wind deflector, and electrical junction box. Weather Armor* enclosures (which are also provided for 09DC016) have a baked enamel finish which provides maximum weather protection. Capacities 15 Tons and Over
PRESSURE DIFFERENTIAL (difference between cylinder load and unload points) is adjustable from 6 to 22 psig (41.4 to 152 kPa). To adjust, turn pressure differential adjustment screw (Fig. 12) counterclockwise to its back stop position. In this position, differential is 6 psig (41.4 kPa). Next, turn adjustment clockwise to desired pressure differential setting. Every full turn clockwise increases differential by 1.5 psig (10.3 kPa). Head Pressure Control — Fan cycling is a standard feature. The no