Votes - 5, Average rating: 4.2
(
)
)
|
manual abstract
Therefore, it is recommended to have someone assist you during the installation of this unit. Installation Select the Best Location A. This room air conditioner is designed to fit easily into a single or double hung window. However, since window designs vary, it may be necessary to make some modifications for safe, proper installation. B. Make sure window and frame are structurally sound and free from dry and rotted wood. C. For maximum efficiency, install the air conditioner on a side of a house or building which favors more shade than sunlight. If the unit is in direct sunlight, it is advisable to provide an awning over the unit. D. Provide sufficient clearance around the cabinet to allow for ample air circulation through the unit. See Fig. 2. The rear of the unit should be outdoors and not in a garage nor inside a building. Keep unit as far away as possible from obstacles/obstructions and at least 30"(76.2cm) above the floor or ground. Curtains and other objects within a room should be prevented from blocking the air flow. E. Be certain the proper electrical outlet is within reach of the installation. Use only a single outlet circuit rated at 15 amps. All wiring should be in accordance with local and national electrical codes. F. DO NOT USE "REGULAR" EXTENSION CORDS WITH THIS UNIT. If it is necessary to use an extension cord to connect your air conditioner, use an approved "air conditioner" extension cord only. (available at most local hardware stores) G. DO NOT install unit where leakage of combustible gas is suspected. Your air conditioner may fail to operate in air containing oils (including machine oils), sulfide gas, near hot springs, etc... 5 Your unit is designed to evaporate condensation under normal conditions. However, under extreme humidity conditions, excess condensation may cause basepan to overflow to the outside. The Unit should be installed where condensation run-off cannot drip on pedestrians or neighboring properties. 1. Assembly of the Upper Channel, to Cabinet. (Factory installed on some models) • "L" Shaped Top Channel: Install the "L" shaped channel to the top of the cabinet as shown in Fig. 3 using four (4) 3/8" (9.5mm)screws. 2. Assembly of the Side Curtains to Cabinet. • Extend the shutter from the shutter frame and slide it into the shutter guide on the side channel of the air conditioner as shown in Fig. 4. • Slide the shutters into the top (“L” Shaped) and bottom (“U” Shaped channels. The shutters are identified (on frame) as left & right. 3. Completing the Installation * Cut the foam (non adhesive) sealing strip to fit the area of the window sill that the air conditioner will rest on. 3a. Completing the Installation (cont’d) • Carefully place the air conditioner into the window with the “L” shaped mounting bracket (on top) positioned in front of the upper window sash. The bottom of the cabinet should be positioned on the “recessed” portion of the window frame. Pull the window down until it rests just behind the front flange of the (top) “L” shaped mounting bracket. See Fig. 5. • Expand the shutter frames (fully) on each side and secure the top of the frames to the window sash using one 3/4" (19.1mm)screw on each side and one in the “L” shaped mounting bracket. Fig. 5 • Secure the shutter clamp on each side of the (lower) shutter and secure to window sill using one 3/4" (19.1mm)screw on each side. Fig.5 Window Sash Place the second foam sealing strip to fit the opening between the inside and outside windows then attach the safety lock to the outside window frame using one 3/4”(19.1mm) screw. See Fig. 6 PLEASE NOTE: Window applications come in a variety of different styles. Therefore, it may be necessary to modify or improvise your particular installation. 6 Key Pad Features LED DISPLAY: Displays the following information independently; Set Temperature, Ambient Room Temperature and Auto Timer On/Off settings. d) POWER: TurnsunitOn/Off. mode MODE: Allows you to scroll through and select V the desired operating mode; Cool 4^ , Dry Fan Only and *Auto B. The selected mode will be denoted by the adjacent indicator light. *‘Auto’ is a pre-set factory program that automatically defines the mode (Cool or Dry) and fan speed based on the set temperature. FAN SPEED: Selectfrom fourdifferentfan settings; Low £o, Medium §§, High ^ and Auto CS39 during Cool and Fan Only mode. Please note: During ‘Dry’ mode the fan speed is automatically defined. 0-Q- ENERGY SAVER: Automatically cycles the fan on and offwhile the compressor is not in use. TEMP /TIMER Control: Used to increased or decreased the Temperature setting in 1°C/ °F increments.and Auto-Timer On/Off settings in 30 min./1hr. increments. Note: This appliance allows you select the temperature scale to be displayed in either “Celsius” or Fahrenheit” according to your preference. To change the temperature scale displayed on the electronic display, press both the “Temp/Timer” adjust arrows simultaneou...