Votes - 0, Average rating: 0
(
)
)
|
Other manuals for this model:
manual abstract
HP PN: D9387-80202 FRONT SIDE
HP NetServer E800 Technical Reference Card
HP Product No. D9387-80202
Power Supply
A Cabinet/Front LEDs
Shelf 1: Flexible Disk
B Mass Storage Device Locations and Settings
Shelf 2: CD-ROM
Shelf 3: Optional Tape Drive
System Board
(Included in Certain Models)
Device
Location in order of
Device Settings
Shelf 4: Hard Disk Drive
recommendation
(Included in Certain Models)
Standard Hard Disk Drive
Shelf 4
SCSI ID 0 [Default]
(Model 9.1 GB)
Shelves 5, 6, 7
HP Accessory 4.2 GB HDD or
Shelf 5, 6, 7
For Additional HDD, Set to
Front LED Indicator
HP Accessory 18.2 GB HDD or
Unused SCSI ID
Below Shelf 3
HP Accessory 36.4 GB HDD
System Power Switch
System Power Indicator
HP SureStore T20i
Shelf 3
SCSI ID 4 [Default]
Off-System is Off
HP SureStore DAT 8i or 24i(Bundled) Shelf 3
SCSI ID 2 [Default]
Solid Green-System is Running
Standard SCSI Controller
Embedded
SCSI ID 7
Do not operate
Blinking Green-System is in
without air duct.
Standard IDE CD-ROM
Shelf 2
Set to Master [Default]
Sleep Mode
Hard Drive Activity Indicator
Flashing Yellow-IDE or
SCSI Activity
Cage for additional HD Drives
See documentation with each device for further configuration information.
C System Board
Chassis Fan
Prossesor 1
(CPU 1)
Power
DIMM Slots
0 1 2 3
System Switch Settings
Mouse
Cautions:
1 2 3 4
Keyboard
On
Do not mix CPU types or speeds. Both CPU's must
Off
CPU 1 Fan
LAN
be the same type and speed.
Off
On = Clear Configuration
Serial A
Unused
On = Clear Password
Terminator is required in secondary CPU slot when
FDD
second CPU is not installed.
Parallel
IDE 1
The Air Duct and all covers and panels must be
DIMM Installation
in place to provide controlled airflow for system
Prossesor 2
Serial B
• Use Only HP buffered DIMMs
reliability.
(CPU 2)
CPU Terminator
•
Video
Any combination (mix or match) of up to four
each of 128MB, 256MB or 512MB DIMMs
SVGA
IDE 2
• Order of Installation is Slot 0, 1, 2, 3 with largest
PCI Slot 1
CPU 2 Fan
DIMMs installed in the lowest Slot number
IRQ Sharing
PCI Slot 2
SCSI (A&B)
PCI 3
PCI Slot 3
SCSI A
Default Boot Order
Emb LAN
PCI 4
PCI Slot 4
PCI 1
PCI 5
1. IDE CD-ROM
7. PCI 3
Status Panel
PCI 2
PCI 6
2. FDD
8. PCI 4
PCI Slot 5
3. Embedded SCSI A
9. PCI 5
Config
PCI Slot 6
4. Embedded SCSI B
10. PCI 6
Switch
5. PCI 1
11. PCI 7
PCI Slot 7
6.
PCI 2
Not Used
SCSI B
For additional information, see other side.
HP PN: D9387-80202 BACK SIDE
HP NetServer E800 Technical Reference Card
HP Product No. D9387-80202
D Mass Storage Cabling/Rear LEDs
E
When removing the Power Supply,
Power Cabling
disconnect its four connectors from
the harness along dotted line. Retain
Power
Built-in SCSI Terminator
the other harness.
Receptacle
BP4
Shelf 1
FDD
Power Supply
Shelf 1
FDD
Unit
Shelf 2
CD-ROM
P1
A
Shelf 2
CD-ROM
Shelf 3
Reserved for Tape Drive
P2
Shelf 2
Shelf 3
Reserved for
BP2
BP3
BP1
System Board
(Optional)
B C
BP2
BP3
BP1
Tape Drive
Power Supply
P3
Shelf 4
Hard Disk Drive
Harness
FDD Connector
Shelf 4
Hard Disk Drive
Shelf 5
P4
(Some Models)
Shelf 5
ATX Connector
Reserved for
Primary IDE
Shelf 6
P5
Hard Disk Drives
Secondary IDE
Reserved for
Shelf 6
Shelf
Shelf 7 6
Hard Disk Drives
P6
Shelf 6
Shelf 7
System
Board
SCSI A
SCSI B
Cables
Part Number
Rear LED Indicator
Flexible
A Disk
D5183-9849
Key to Mounting Screws
On LAN Connector
Cable
Snap
Activity Link Indicator
LAN Speed Indicator
IDE
Visible when Cables and Processors
Steady Green-Link Valid
OFF-10Mbps
B CD-ROM D5184-9420
LED
LED
1
2
Cable
have been Removed.
Blinking Green- Activity
Steady Yellow-100Mbps
SCSI
on LAN
C
D5184-9419
Snaps
Cable
Note: For complete instructions,
F
see the Information Assistant on the
Service Information
G Tips for Removing
HP Documentation CD-ROM.
the System Board
Electronic Support Services
• Internet Web Pages http://www.hp.com/netserver
• Unplug Power, Remove Cover
Audience Assumptions
• Internet FTP ftp://ftp.netserver.hp.com
• Retract Feet, Lay Unit on Right Side
This Technical Reference Card is for trained service
• CompuServe Library GO HPPC
• Swing Air Duct Open
3
4
5
personnel. Hewlett-Packard Company assumes you
• HP Navigator CD
are qualified in the servicing of computer equipment
• Disconnect All Cables
Support Questions
and trained in recognizing hazards in products with
from System Board
hazardous energy levels.
• HP-Authorized Reseller
• Take out CPUs (If Only One CPU
• CompuServe Discussion Forum GO HPPC
Electrostatic Discharge
Present, Also Remove Terminator
• US / Canada Phone Support 1-208-331-2767
To avoid catastrophic or hidden damage to components,
from Second Slot)
• Europe Phone Support (+31-20) 581-3330
wear a wrist strap and use a static-dissipative work
(Netherlands)
• Take out All PCI Cards
surface connected to the chassis when handling
HP has offices in over 100 countries. Check
components. Use an antistatic service kit, such as
• Remove All 7 Screws (See Illustration)
your local telephone directory.
3M 8501/8502/8505 or equivalent.
• Grasp and Unsnap the Snaps
Optional HP 3 Year On-Site Support Pack
6
7
This information is subject to change without notice
at Corners Opposite Back Panel
and is provided without warranty.
• H5525A Next Business Day
• Swing Edge Opposite Back Panel Outward
Snap
• H5517A Same Business Day
© Copyright 2000. Hewlett-Packard Company
• Slide Board Out Carefully
• H5512A 7 day/24 hour
For additional information, see other side.