Login:
Votes - 1, Average rating: 4 ( )

User manual Bloomfield, model 2074

Manafacture: Bloomfield
File size: 1.86 mb
File name:
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


MAIN WARMER PLATE is turned ON automatically at the start of a brew cycle. Because coffee loses its freshness after sitting on a warmer, a quality time function is included. The WARMER LEDS will begin to flash some time after the last brew cycle, based on the QUALITY TIME setting. Note: QUALITY TIMER does not turn off the warmer elements. 6. The unit will revert to the energy-saver mode some time after the last brew, based on AFTER HOURS TIME setting. WARNING: RISK OF INJURY The following servicing sections are for operator reference only. All servicing and/or repairs must be performed by a qualified technician Reset Hi-Limit Thermostat 240 V & Dual Voltage Units WARMER WARMER ELEMENT FILL SOLENOID WATER LEVEL PROBE CONTROLLER FILL WARMER BREW BREW SOLENOID BREW CANCEL CONTROLLER BREW BREW TIME DRIP OUT TIME WATER TEMP PROBE TRIAC HEATING ELEMENT T HI-LIMIT STAT LINE VOLTAGE CONTROLLER HEAT BREW TEMP CONTROLLER QUALITY TIME 14 SERVICING INSTRUCTIONS - ELECTRICAL (continued) 15 ITEM DESCRIPTION PART N0. USED ON 3 PROBE, TEMPERATURE 83480 ALL 4 THERMOSTAT, HI-LIMIT SAFETY (120V) 83949 2012, 2072 5 GROMMET, TEMP PROBE 84063 ALL 7 SENSOR, WATER LEVEL 83521 ALL 8 SLEEVE, WATER LEVEL SENSOR 83532 ALL 15 ELEMENT, HEATER 1500W (120V) 83518 2012, 2072 ELEMENT, HEATER 1200W (120V) 83747 2012CA, 2072CA ELEMENT, HEATER 3200 W (240V) 83748 2016, 2074 17 ASSEMBLY, TRIAC & HEATSINK 83475 ALL 20 CONTROLLER 83474 ALL 27 COVER PLATE, WARMER 8700-16 ALL 28 ELEMENT, WARMER, 100W (120V) 8572-18 ALL 33 POWER CORD (120V) 6407-15 2012, 2072 34 STRAIN RELIEF, POWER CORD 35-210 2012,2072 36 OVERLAY DECAL, KEYPAD 87020 ALL 39 TERMINAL STRIP, 4-POLE 2016, 2074 41 SWITCH ROCKER ON-OFF THERMOSTAT, HI-LIMIT SAFETY (240V) 8552-50 ALL except 2012, 2072 82936 2016, 2074 8552-18 SERVICING INSTRUCTIONS — DE-LIMING WATER HEATER TANK SERVICING INSTRUCTIONS — DE-LIMING WATER HEATER TANK CAUTION - CHEMICAL BURN HAZARD De-liming chemicals are caustic. Wear appropriate protective gloves and goggles during this procedure. CAUTION -CHEMICAL BURN HAZARD Never siphon de-liming chemicals or solutions by mouth. This operation must only be performed by qualified and experienced service personnel. IMPORTANT: DO NOT spill, splash or pour water or de-liming solution into or over any internal component other than the inside of the water tank. IMPORTANT: DO NOT allow any internal components to come into contact with the de-liming solution. Take care to keep all internal components dry. NOTE: Repeat steps 4 thru 7 as required to remove all scale and lime build-up. NOTE: Normally, silicone hoses do not need to be de-limed. Should de-liming hoses become necessary, Bloomfield Industries recommends replacing the hoses. 1. Disconnect brewer form the electrical supply. Turn off the water supply and disconnect water supply from the brewer inlet fitting. 2. Remove the top panel or top warmer section to gain access to internal components. 3. Disconnect water level sensor and water temperature sensor from the controller. On 120V units, slip hi-limit thermostat from under its holder clip. Disassemble the three lid clips and lift the lid off of the water tank. Store lid assembly in a safe location. 4. Mix de-liming solution according to the manufacturer’s directions. Add the de-liming solution to the water tank. Set lid assembly back on tank. Allow to sit for 30 minutes, or as directed by the manufacturer. 5. At end of soaking period, remove lid assembly from tank. Thoroughly rinse interior components of lid assembly with clear water. Wipe temperature sensor and water level sensor with a clean, soft cloth. Store lid assembly in a safe location. 6. Using a stiff bristle brush, scrub the coils of the heating element and the interior surfaces of the water tank. 7. Siphon the used solution and loose lime/scale into an appropriate container. Dispose of the used solution as required by local ordinances. CAUTION: Never siphon by mouth. Serious injury can result! 8. Fill the water tank with clean tap water. Rinse thoroughly, then siphon the rinse water into an appropriate container for disposal. Again, take care to keep all internal components dry. 9. Reassemble the tank lid to the water tank. Make sure the gasket is properly attached to the lid before assembling the lid clips. Re-connect the water level and temperature probes, then reinstall the hi-limit thermostat (if removed). Verify that all internal components are dry, then reinstall the top panel. 10. Reconnect brewer to water and electrical. Run and discard at least three full decanters from the faucet. Install the brew chamber without filter paper or grounds, then run and discard at least three full decanters as normal brew. 11. Brewer is ready to use. 16 TROUBLESHOOTING SUGGESTIONS TROUBLESHOOTING SUGGESTIONS If the E-Max™ goes into the error diagnostic mode as outlined below, it will likely be necessary to reset the brewer in order to test individual components. Note the reset procedure below: * For the first four error ...

Other models in this manual:
Coffee Makers - 2016EX (1.86 mb)
Coffee Makers - 2074FRL (1.86 mb)
Coffee Makers - 2074L (1.86 mb)
Coffee Makers - 2012 (1.86 mb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category