The Homeowner must contact a qualified service technician at once if any abnormal condition is observed. Small Area Paint Touch-up The finish of the appliance is a high quality powdercoat. Only use factory supplied powdercoat paint kit for touch-ups. Paint is available at your local authorized Superior Hearth Products dealer, cat. no. 90L74. Never attempt to paint a hot fireplace. Do not attempt to repaint the appliance until the finish is completely cured (see Burn-In Period on Page4). Ifthesur

Figure 11 illus- trates two methods for connecting the gas supply. Installation methods and materials must be in compliance with local codes. The gas control valve is located in the lower control compartment. To access the valve open the lower control compartment door (Figure 12). The control valve has a 3/8" NPT thread inlet port and is fitted with a 3" (76 mm) long nipple, 3/8" NPT on both ends. Plan the connections accordingly. We recom- mend that the gas line be routed for the left side of t

mmH J L M N P QK M Front View H L K J Q N P Top View Flue Outlet for B-Vent Connection: 35 Models = 4 in. (102 mm) 40 Models = 5 in. (127 mm) 9-1/4 in. (235 mm) 1/2 in. (13 mm) 1-5/8 in. (42 mm) Right Side View 9-1/2 in. (241 mm) Optional Electrical Inlet Knockout requiring a field-provided Junction Box (Either Side) ELECTRICAL INLET 2-3/4 in. x 2 in. (70 mm x 51 mm) COVER PLATE with KNOCKOUT (Right Side) 16 in. (406 mm) Hood Left Side View 5-7/8 in. (149 mm) *NOTE: It is recommended that gas be

Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water. OPERATING INSTRUCTIONS 1. STOP! Read the safety information above on this label. 2. (If applicable) Set the thermostat to lowest setting. Turn wall on/off switch, unit mounted on/off switch or remote control switch "OFF." If used, remove the batteries from the battery holder. 9. Close control compartment. 10. If the appliance will

The fireplace has a built-in thermostat so it will shut off automatically once the pre-set temperature is reached. It will also turn on automatically if the room temperature drops below the pre-set temperature. 7. To adjust the height of the flame, press the “+” or “-” buttons. To increase the height of the flame, press the “+” button, to decrease the height of the flame, press the "-" button. There are seven levels of flame effects. 8. To turn off the fireplace, press the ON/OFF button once. NO

when (Ht) > (Vt) Simple venting configurations FIGURE 14 FIGURE 12 H 1 H 2 V 3 V 1 90° 90° 90° V 2 90° H 4 V 1 V 2 90° 45° 90° H 1 90° H 3 H 2 TOP EXIT VERTICAL TERMINATION MAXIMUM VERTICAL RISE IN FEET VT HORIZONTAL VENT RUN PLUS OFFSET IN FEET H T The shaded area within the lines represents acceptable values for HT and VT . INSTALLATION WALL AND CEILING PROTECTION FOR SAFE AND PROPER OPERATION OF THE FIREPLACE, FOLLOW THE VENTING INSTRUCTIONS EXACTLY. NOTE: Only a clearance to combustibles of

Replace the black louvers with the brass or brushed stainless louvers (without the pre-drilled holes) using the existing brackets. Step 5. Repeat Step 4 for the bottom louver assembly. Make sure to replace the pre-drilled black louver with the pre-drilled brass or brushed stainless louver. Existing Bracket Center Bracket (For No.’s H1526 thru H1529 Only) Existing Bracket Existing Bracket Figure 1 Center Bracket (For No.’s H1526 thru H1529 Only) Existing Bracket Louver (With Pre-Drill

This will reduce the velocity of the exhaust gases, slowing down the fl ame pattern and creating a more traditional gentle appearance. Specifi c instructions are included with the kit. 10.3 FLAME CHARACTERISTICS It’s important to periodically perform a visual check of the pilot and burner fl ames. Compare them to the illustrations provided. If any fl ames appear abnormal call a service person. PILOT 3/8” - 1/2” BURNER FLAME MUST ENVELOP UPPER 3/8” TO 1/2” OF FLAME SENSOR FLAME SENSOR ELECTRODE 5

VERTICAL RISE IN FEET V T HORIZONTAL VENT RUN PLUS OFFSET IN FEET H T The shaded area within the lines represents acceptable values for H and V TT . For vent configurations requiring more than one 90° elbow, the following formulas apply: Formula 1: H < V T T Formula 2: H T Example 1: FIGURE 6 V 1 =3 ft V 2 =8 ft V T = V 1 + V 2 = 3 + 8 = 11 ft H 1 = 2.5 ft H 2 =2 ft H R = H 1 + H 2 = 2.5 + 2 = 4.5 ft H O =.03(three 90° elbows - 90°) = .03(270° - 90°) = 5.4 ft H T = H R + H O = 4.5 + 5.4 = 9.9 ft

extrusion trims.extrusion trims.extrusion trims.extrusion trims.extrusion trims. Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves, Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves,Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves,Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves,Electrical (110V and millivolt) components and wearable pa