may make direct contact with sides and top around the fireplace face. It is important that combustible materials do not overlap the face itself. Brick, glass, tile or other noncombustible materials may overlap the front face provided they do not obstruct essential openings like louvered slots or any other opening. When overlapping with a noncombustible facing material, use only noncombustible mortar or adhesive. Optional Gas Line Installation Gas line hook up should be done by your supplier or a

you can control the room temperature with the thermostat .. . Turn the Thermostat . to the "max“ position. As soon as the desire room temperature is reached... . Turn the Thermostat . back till you hear an audible click. The in-built thermostat now ensures a constant room temperature. Flame regulator With the Flame regulator . you can regulate the flame to any size. . Turn the Flame regulator . in the clock-wise direction until the desired flame size is obtained. Replacing the bulbs Danger of l

A. This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to light the pilot by hand. B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electric switch. • Do not use any phone in your building. • Immediately call your gas supplier from a neighbor.s phone.

Have a qualified technician replace pilot line 6. Replace control valve (Refer to Replacement Parts, page 28) 7. Check that main power is on and that all wire connections are made correctly to the ignition model (see Wiring Diagram, page 23). Check for 24 VAC at the secondary side of the transformer. If 24 VAC is present and the module does not operate, have the module replaced otherwise have the transformer replaced 1. Check wiring connection. Refer to wiring diagram (see Wiring Diagram, page 2

Fabricate a hearth extension using a material which meets the following specifications: a layer of noncombustible, inorganic material having a thermal conductivity of K=0.84 BTU IN/FT, HR. F (or less) at 1" thick. For example, if the material selected has a K factor of 0.25, such as glass fiber, the following formula would apply: 0.25 x 1.0" = 0.30" thickness required 0.84 Thermal conductivity "K" of materials can be obtained from the manufacturer or supplier of the noncombustible material. If t

(V)V36EN (V)V36EP (V)V36ENS (V)V36EPS (V)V36ENH (V)V36EPH DESCRIPTION QTY. 1 ** ** ** Firebox Assembly 1 2 ** ** ** Face Weldment 1 3 108010-01 108010-02 108010-01 108010-02 108010-01 108010-02 Door Assembly (V Models Only) Door Assembly (VV Models Only) 1 4 108011-01 108011-01 108011-01 Top Panel Louver Assy 1 5 108011-02 108011-02 108011-02 Bottom Panel Louver Assy 1 6 ** ** ** Fireplace Top 1 7 ** ** ** Fireplace Top Insulation 1 8 ** ** ** Fireplace Surround 1 9 109082-01 109082-01 109082-01

If it goes out, repeat steps 5 through 8. • If gas control knob does not pop up when released, stop and immediately call your service technician or gas supplier. • If the pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call your service technician or gas supplier. 9. Turn on all electric power to the fireplace. 10. Turn gas control knob counterclockwise to “ON”. 11. This valve is equipped with a HI/LO feature. Set fireplace input as desired. 12. Close lower lo

The groove line on the side of the brick will come in contact with the flange on the brick housing. This secures the brick into the housing. See Figure 20 on page 14. The bricks are packaged in four separate boxes. These boxes are labeled by sections of the firebox. Box #1 - Hearth Panel Box #2 - Rear Panel Box #3 - Left or Right Panel Box #3 - Left or Right Panel 117541-01A 14 117541-01A Install the bricks one at a time starting with the hearth panel followed by the rear panel and then the left

20' max. The following configurations show the minimum vertical rise requirements for a horizontal system using two 90° elbows. 45° Elbow Figure 17 - Horizontal Termination Configuration for Venting Using Two 90° Elbows 116647-01A 12 VENTING INSTALLATION INSTRUCTIONS Installation Planning (Cont.) Installation for Vertical Termination VENTING INSTALLATION INSTRUCTIONS Figure 18 - Horizontal Termination Configuration for Venting Using Two 90° Elbows with Termination at 90° with Fireplace Continued

When calling DESA, have ready • model number of your fireplace • the replacement part number Service Hints When Gas Pressure Is Too Low • pilot will not stay lit • burners will have delayed ignition • fireplace will not produce specified heat • propane/LP gas supply might be low (propane/LP units only) You may feel your gas pressure is too low. If so, contact your local gas supplier. Technical Service You may have further questions about installation, operation, or troubleshooting. If so, contac