Votes - 2, Average rating: 3.5 ( )

Manafacture: FireplaceXtrordinair File size: 5.89 mb File name: Language of manual:

Hearth extensions are not required for these fireplaces. Louvers and decorative louver panels are interchangeable, and may be mixed and matched as desired. Attention: Flush panels may not be used on these models. Page 16 26670-0-0110 26670-0-0110 Page 17 The fireplace is designed to accept a gas line for connection to the gas valve. Have the line installed by a qualified service person in accordance with all building codes. Consult local building codes to properly size the gas supply line leading to the connection of the valve. The state of Massachusetts requires that a flexible appliance connector cannot exceed three feet in length. Gas access holes are provided through the side panel(s) of the fireplace. See Figure 14. Check gas type. Use only the gas type indicated on the rating plate. If the gas listed on the plate is not your type of gas supply, DO NOT INSTALL. Contact your dealer for proper model. Always use an external regulator to reduce the supply tank pressure to a maximum of 10.5" w.c. (NAT), or 13" w.c. (LP) See page 10. WARNING: CONNECTION DIRECTLY TO AN UNREGULATED L.P. TANK CAN CAUSE EXPLOSION. Figure 14 GAS LINE CONNECTION GAS LINE ACCESS HOLES PLACEMENT oF GLoWING EMBERS AND LAVA RoCK PLACEMENT oF GLoWING EMBERS AND LAVA RoCK Placement of the glowing embers (rockwool) is very individual and light coverage of the areas indicated will provide your best effects. We recommend separation of the rockwool by hand and to make your coverage as light and fluffy as possible. Place just enough embers on the burner to obtain the glow and a gold yellow flame. Do not place rockwool over large port areas. Rockwool should not be placed in the area of the pilot assembly. Over time, the rockwool will break down and new rockwool will need to be placed to recreate the original glowing embers effect. Remove all old rockwool from the appliance and apply new rockwool as shown in Figure 15. Note: Only the rockwool supplied with this unit or ordered in accordance with the Parts List on pages 30 and 31 should be used on this burner. See the Parts List on pages 30 and 31 to order replacement rockwool. placing Lava Rock in front of Burner on fireplace floor Spread lava rocks on fireplace floor in front of the burner pan. The lava rocks are for decorative effect and are not required for fireplace operation. ATTENTION: DO NOTPLACE LAVAROCKS ON BURNER, LOGS OR ROCKWOOL. THE LAVA ROCKS SHOULD ONLY BE PLACED ON THE FIREPLACE FLOOR. Do not cover any large ports withDo not cover any large ports with ember material (glowing embers) ember material (glowing embers) Placeembermaterialonlyoverportareasasshown Placeembermaterialonlyoverportareasasshown LP BURNER -TOP VIEW NAT BURNER -TOP VIEW Figure 15 Page 18 26670-0-0110 oPERATIoN INSTRUCTIoNS/FLAME APPEARANCE oPERATIoN INSTRUCTIoNS/FLAME APPEARANCE Before you begin: Do not handle the logs with your bare hands! Always wear gloves to prevent skin irritation. After handling logs, wash your hands gently with soap and water. All Logs The positioning of the logs is critical to the safe and clean operation of this heater. Sooting and other problems may result if the logs are not properly and firmly positioned in the appliance. Instructions for placement of the logs in the fireplace are included with the logset. The logset approved for use is the LSU24RR-2, and must be ordered separately. Flames from the pilot (rear right back side of the pan burner) as well as the main flame should be visually checked as the log set is installed. In normal operation at full rate after 10 to 15 minutes, the flame appearance should be sets of yellow flames. Natural gas burners will tend to have blue flames with yellow flame tips. NOTE: All flames will be random by design, flame height will go up and down. Glowing embers (rockwool) can cover the pan burner in between the front and middle logs, but very little is necessary to cover this area. Excess ember material causes the yellow flame to become orange and stringy. Apply just enough to obtain slow glow and a gold yellow flame. Avoid any drafts that alter burner flame patterns. Do not allow fans to blow directly into fireplace. Do not place a blower inside the burner area of the fireplace. Ceiling fans may create drafts that alter flame patterns. Sooting and improper burning will result. During manufacturing, fabricating and shipping, various components of this appliance are treated with certain oils, films or bonding agents. These chemicals are not harmful, but may produce annoying smoke and smells as they are burned off during the initial operation of the appliance, possibly causing headaches or eye or lung irritation. This is a normal and temporary occurrence. The initial break-in operation should last 2-3 hours with the burner at the highest setting. Provide maximum ventilation by opening windowsor doorstoallowodorsto dissipate.Anyodors remaining after this initial break-in will be slight and will disappear with continued use. pERIODIC CLEANINg – Refe...

Download now

Please, enter two numbers from picture: