Votes - , Average rating:
(
)
)
Manafacture: GN National Electric
File size: 2.59 mb
File name:
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
WARNING: 1. The use of substitute glass will void all product warranties. 2. Care must be taken to avoid breakage of the glass. 3. Under no circumstances should this appliance be operated without the glass front or with a broken glass front. Replacement of the glass (with gasket) as supplied by the manufacturer must be done by a qualified service person. 4. Do not abuse the glass by striking or hitting the glass. WARNING: Do not use abrasive cleaners on glass. Do not attempt to clean glass when glass is hot. Glass Assembly Replacement 1. Remove cabinet top. 2. Pivot left and right front panels open. 3. Release two door latches on left and right of firebox. 4. Grasp glass frame and carefully pull toward you. 5. Place glass frame assembly on non-abrasive surface. The exterior of the glass frame assembly should be facing the nonabbrasive surface. 6. Insert a putty knife between glass and bottom corners on frame. Carefully separate glass from frame. 7. Use putty knife to remove silicone and gasket material from frame. Surface of frame must be clean and dry. 8. At each corner of frame apply two (2) three inch beads of high temperate (orange) silicone. 9. With thin gasket on glass facing silicone on frame, insert glass into frame. Carefully press the glass onto frame in order to have contact between glass and silicone. 10. Allow silicone to set-up for an adequate time. 11. Gently place glass frame back into firebox. 12. Close the 2 door latches on left and right of firebox. 13. Pivot left and right front panels closed. 14. Replace cabinet top. UNIT OPERATING FAULTS SERVICE AND INSTALLATION OF THE APPLIANCE SHOULD BE CARRIED OUT BY AUTHORIZED PERSONNEL ONLY. heat output, carbon build up or sooting, bad odors, rattles or other sounds, start up failures and burner(s) switching themselves off. These are nearly always the result of improper installation or in- THE MAJOR CAUSE OF OPERATING PROBLEMS WITH GAS FIREPLACE HEATERS IS IMPROPER GAS PRESSURE, INCORRECT LOG PLACEMENT, IMPROPER INSTALLATION, INCORRECT FLUE INSTALLATION, INCORRECT SWITCHING OF BURNERS, DIPS/SPIKES IN THE INCOMING POWER OR REVERSE POLARITIES. The above situations can cause such problems as changes in flame color or configuration, intermittent operations, changes in correct operation and it may take sometime for these problems to show themselves. Before calling out a technician you must be able to repeat the fault, try resetting the heater. Read below. Note: Incorrect installation of the unit, logs, flue pipe, gas pressure or operation, which cause the above mentioned faults, are not covered under warranty and a service call fee will be charged to correct such problems. RESETTING THE HEATER There are a number of reasons why sometimes the heater will switch itself off and is the correct thing for the heater to do in certain situations (i.e. overheating, power failure or dips, windy conditions, pump failure, partial or full blockage of flue pipe or no gas. All of these operations are monitored by the electronic control box inside the heater, which is heat sensitive, pressure switch sensitive, flame sensitive and water sensitive. If one of these items is not correct, the heater will shut itself down. To reset, turn both burner switches to the OFF position, ensure the red button above the two burner switches is not illuminated (if a Remote Control is fitted, have it in the off mode). Then turn the power off at the power point for approximately 10 seconds. Then turn the power point back on and the power L.E.D. should be illu minated. If you have a Remote burner switch and the rear burner L.E.D. should start flashing, with the flue fan L.E.D. remaining steady. Wait approximately 60 seconds for the rear burner to ignite. You can tell when it has lit, even if you can’t see any flames, by looking at the rear burner L.E.D. which should remain steady. Repeat the same process with the front burner. Turn on the front burner switch and wait approximately 60 seconds and the front burner L.E.D. will remain steady. In approximately 5 minutes the convection fan should start and the heater has been successfully reset. Note: if the heater is still warm when reset the convection fan may already be running when the unit is powered up. Page 38 22618-4-1106 LOG PLACEMENT If for any reason a log should need replacement, you must use the proper replacement log. Consult your Mantis dealer for correct replacement logs. Note: Improper positioning of logs can create carbon build up and will alter the unit’s performance and operation. Replacement logs must be installed and positioned as outlined on pages 16 through 17 under Log Installation. MAIN CONVECTION FAN The main convection fan in the heater should be checked, ser-Note: If the main convection fan becomes clogged with lint and viced and cleaned annually by a qualified service person to ensure dust an over-temperature situation will occur through the that your appliance is operating efficiently. heater exchange system and th...
Other models in this manual:Fireplaces - BP)-1 (2.59 mb)
Fireplaces - CP (2.59 mb)
Fireplaces - GN (2.59 mb)
Fireplaces - GP)-1 (2.59 mb)