Votes - , Average rating:
(
)
)
Manafacture: Dimplex
File size: 275.14 kb
File name: 7203810100REV08.pdf
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
4. Use studs to frame an opening of 261/2" wide X 23" high (67.3cm wide X 58.4crn high) allowing a depth of 12· (30.5cm). (Refer to FIGURE 3 as an example.) 5. Plan your electric power supply: (Refer to Note 1) Option #1 -The power cord can be lead from behind the trim and along the wall to an outlet near the fireplace. (FIGURE 4) Option #2 -A new outlet can be installed inside the new frame construction. (FIGURE 5) OUTLET FIGURE 5 FOR BATHROOM USE Must be protected by a GFI receptacle or circuit if receptacle is used it must be readily accessible. To prevent electrical shock this unit is an electrical appliance that is not watertight and must be installed as to prevent water from entering unit. This must be installed away from showers, tubs, etc. Never locate fireplace where it may fall into a bathtub or other water container. Keep towels and other combustible materials 3 feet away from the front of the unit. 3A WARNING ·Construction and Electrical Outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electric shock and injury to persons. ·Construction and Electrical Outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electric shock and injury to persons. Dimplex Mantel Surround Kit or custom made mantel surround: 1. Select a suitable location that is not susceptible to moisture and is away from drapes, furniture and high traffic. 2. Place the Fireplace in the desired location to see how it will look in the room. 3. For ease of electrical hook up you may wish to locate the Fireplace near an existing outlet. (Refer to Note 1) 4. Store the Fireplace in a safe, dry and dust free location. 5. Assemble Mantel Surround Kit (Refer to instructions provided with the Mantel Surround Kit) or construct the custom surround with an opening of 26 1/2" wide X 23" high (67.3cm wide X 58.4cm high) allowing a depth of 12" (30.5cm). WARNING ·Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric shock or injury to persons, always use a licensed electrician. FIREPLACE INSERT INSTALLATION This section provides easy step by step instructions for installation of your Fireplace: INSERT 1. Install Trim Kit to front of Fireplace by positioning trim then pushing straight forward against the Fireplace. 2. Make sure the unit is switched OFF (Refer to operating instruction section). WALL OR MANTEL TRIM 3. Plug the Fireplace into a 15AMP/120Volt outlet. If the cord does not reach you may use an extension cord rated for a minimum of 1875 WATTS. 4. Push the Fireplace into place so that the trim is against the finished Mantel Surround or wall surface. (FIGURE 6). PUSHFIGURE 6 5. Level, if required with wood shims (not included) (FIGURE7). WARNING ·Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure that the power cord is stored or secured to avoid tripping or snagging to reduce the risk of fire, electric shock or injury to persons. OPERATION SHIMS GRILL OPEN HERE ED BC FIGURE 7 FIGURE 8 This section will explain the function of each convenient control. 1. To access the controls, open the upper grill by pulling, near the top, forward and down. (FIGURE 8) 2. To locate controls refer to FIGURE 9. A. MAIN ON/OFF SWITCH The ON/OFF SWITCH supplies power to all fireplace functions (Heater /Flame). RESETTING THE TEMPERATURE CUTOFF SWITCH This unit is equipped with a thermostat which controls the temperature of the room. It does this by turning the heater on and off. The heater is protected with a safety device to prevent overheating. Should the heater overheat, an automatic cut out will turn the heater off and it will not come back on without being reset. It can be reset by switching the ON/OFF SWITCH to OFF and waiting 5 minutes before switching the unit back on. CAUTION ·If you need to continuously reset the heater, unplug the unit and call your local dealer. B. FLAME ACTION CONTROL(certain models only) Turn the flame action control knob to adjust the flame speed to the desired level. 5 FIGURE 9 C. FLAME BRIGHTNESS CONTROL Turn the flame brightness control knob to increase or decrease the brightness of the flame and embers. A D. HEATER ON/OFF SWITCH The heater on/off switch supplies power to the heating unit when main on/off switch (A) is on. E. HEATER THERMOSTAT CONTROL To adjust the temperature to your individual requirements, turn the thermostat control clockwise all the way to turn on the heater. When the room reaches the desired temperature, turn the thermostat knob counter clockwise until you hear a click. Leave in this position to maintain the room temperature at its setting. For additional heat, turn clockwise until you hear the click again and the heater will turn on. To lurn the heater off, rotate the knob fully counter clockwise. NOTE • The heater may emit a slight, harmless odor when first used. This odor is a normal condition caused b...