|
manual abstract
Remove the heater body, two wheelbases, wheels, screws, and washers from the box. Remove the pack- aging materials and keep for future storage. 2. Attach the wheels to each wheelbase with the supplied wheel screws, small black spring-washers, and small grey washers. WHEELBASEWHEELSCREWWHEEL SMALL BLACK SPRING WASHER SMALL GREY WASHER 3. Be certain the heater is unplugged and the controls are set to off. Set the heater on the floor upside down. 4. Attach a wheel base (with wheels attached) to each end of the heater body using the supplied standard screws, large black spring-washers, and large grey washers. LARGE BLACK SPRING WASHER LARGE GREY WASHER MICATHERMIC HEATER OPERATING INSTRUCTIONS CONTROL PANEL 1. Place the heater on a firm, level surface and plug into a grounded 120V 60Hz power outlet. Only operate heater in upright position with caster wheels attached. 2. Once the heater is plugged in, the POWER INDICATION LIGHT will light up. 3. Select a heat setting: On the control panel, turn the POWER SELECT dial to the desired setting: LOW (500W), HIGH (1000W), or ECO mode. 4. Adjust the thermostat by turning the THERMOSTAT dial on the control panel or remote control. You will hear a faint click noise when the thermostat is turned to a point above the current room temperature. Continue to turn the thermostat to increase the room temperature. If the area becomes too warm turn the THERMOSTAT dial down slightly until you reach a point where the temperature is more comfortable. 5. Once you have chosen the desired temperature, the heater will remain on until the room temperature increases to the temperature set on the THERMOSTAT dial. The heater will cycle on and off to maintain the desired room temperature. 6. Unplug the heater when not in use. NOTE: ECO mode is an Economic Energy Saving Function. When ECO mode is chosen the heater will consume one-third less power once the room temperature reaches the set temperature on the digital display. POWER INDICATION LIGHT POWER SELECT DIAL THERMOSTAT DIAL OPERATING INSTRUCTIONS (CONTINUED) OPTIMAL OPERATING CONDITIONS To get the most out of your Soleus Air Micathermic heater, follow these helpful hints: 1. All electric heaters are limited to maximum of 1500 watts* (per UL and ETL requirements). Due to this limitation all electric heaters can heat approximately 150 square feet. Micathermic heaters fit in this category, but they are able to provide a more comfortable and consistent heat than other heating technologies. 2. For optimal performance, place the heater in a room and close all windows and doors. This will confine the heat to the area that needs it most. 3. To save energy and in turn save money in the winter, place the heater in a room or area that needs extra heat instead of raising the thermostat on your central heating system. This heater will function very well as an additional heating source and can easily maintain the temperature in most rooms and attached bathrooms. There is no need to increase the heat in the entire house when you only need comfort in the room in which you are currently located. *The HM1-10-01 & HM1-10-32 produce 1000 watts maximum. MAINTENANCE 1. Unplug the unit and let it cool completely. 2. To keep the heater clean, the outer shell may be cleaned with a soft, damp cloth. You may use a mild detergent if necessary. After cleaning, dry the unit with a soft cloth. CAUTION: DO NOT let liquid enter the heater. 3. DO NOT use alcohol, gasoline, abrasive powders, furniture polish, or rough brushes to clean the heater. This may cause damage or deterioration to the surface of the heater. 4. DO NOT immerse the heater in water. 5. Wait until the unit is completely dry before use. STORAGE Store the heater in a cool, dry location when not in use. If available, use the retail packaging and pack up the heater to prevent dust from collecting on and inside the heater. TROUBLESHOOTING If the heater will not operate, please check the following before seeking repair of service: 1. Check if the power cord is plugged into an electrical outlet, if not, plug in. 2. Check if electricity to the main fuse is working. 3. Check if the heater is set to ON by confirming the light on the control panel is lit. If not, turn the POWER SELECT dial to LOW, HIGH, or ECO MODE to turn on the unit. 4. Check if the heater is on a level surface. If the tip-over safety mechanism inside the heater is engaged the heater will not run. 5. The room temperature has reached the temperature on the digital display of the heater. Increase the temperature on the display so the heater will continue operation or wait for the room temperature to drop below the set temperature on the heater. WARRANTY One Year Limited Warranty Soleus International Inc. warrants the accompanying Soleus Air heater to be free of defects in material and workman- ship for the applications specified in its operation instruction for a period of ONE (1) year from the date of original re- tail purchase in the United State...
Other models in this manual:Electric Heaters - HM1-10-32 (1.92 mb)