Votes - 5, Average rating: 3.6
(
)
)
|
manual abstract
Refer to page 4 for all hardware components. Do NOT attempt assembly unless all components are available. If you believe a component is missing or damaged, contact 1-800-762-1142 for assistance. Additional Requirements The following items are not included, but are necessary for the proper assembly of your heater. Do NOT attempt to assemble without proper tools. (1) - 7/16” Wrench (1) - #2 Phillips Head Screwdriver (1) - Leak Detection Solution (Instructions on how to make solution are included in Step 5) (1) - 20 lb.(4-5 gallon) precision filled LP Gas Grill Cylinder Note: You must follow all steps to properly assemble heater. Step 1 - Attach Emitter Screen • Line up 4 holes on bottom of Emitter Screen with corresponding holes in Emitter Bottom, and insert (4) Medium Screws in holes until tight. 5 Owner’s manual and assembly instructions: 71400 portable outdoor heater 3/3/03 Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Endless Summer Step 2-Attach Top Wire Guard • Line up 4 prongs on Wire Guard Bottom with 4 holes on Emitter Bottom, and Insert. Note: It may be necessary to adjust the prongs slightly to line them up with the holes. Step 3-Attach Dome to Emitter • Line up three studs in Emitter with holes in Dome. Slide Dome carefully over studs, clamping Top Wire Guard securely in place. Note: It may be necessary to adjust prongs of the Top Wire Guard slightly to provide a secure fit. • Install (3) Cap Nuts on studs and tighten with 7/16” wrench. Do not over tighten. Owner’s manual and assembly instructions: 71400 portable outdoor heater 3/3/03 6 Endless Summer Caution: Before you attempt to use a propane cylinder, understand all cylinder and propane related precautions in Section #1 - “Safety First.’ Caution: Your Endless Summer Portable Heater has been checked at all factory connections for leaks. Recheck all connections, as movement in shipping can loosen connections. Check for leaks even if your unit was assembled for you at the store. Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Step 4 - Gas Hook-up Note: For best results, use heater with a 20 lb. cylinder. The pressure regulator and hose assembly supplied with the appliance must be used and replacements must be those specified by the manufacturer. To connect 20 lb. Cylinder • Slip end of flexible gas line with brass fitting through center hole of Base and up to threaded portion of regulator. • Line up threads on fitting with those on regulator and rotate clockwise until snug. HAND TIGHTEN ONLY. DO NOT USE ANY HAND TOOLS TO MAKE THIS CONNECTION. BE CAREFUL NOT TO CROSS THREADS WHEN SCREWING IN FITTING. Note: if heater uses center clamp, hose can be routed through opening in base and table. • Set heater on base, making sure that flexible gas line is routed through small slot in base. • Attach gas line to cylinder by turning black plastic knob counter clockwise into cylinder valve until tight. Note: Be careful not to kink flexible gas line. • When using the gas extension hose always locate the hose out of pathways where people may trip over it or in areas where the hose may be subject to accidental damage. To connect 14.1 oz or 16.4 oz cylinder Note: Some 1-lb cylinders may form frost when near empty. • Line up threads on canister with those on regulator, insert and rotate canister clockwise until they fit snugly together. HAND TIGHTEN ONLY. BE CAREFUL NOT TO CROSS THREADS WHEN SCREWING IN CANISTER. Step 5 - Check for Leaks To check for leaks: • Make 1-2 oz. of leak solution by mixing one part liquid dishwashing soap and 3 parts water. • Spoon several drops (or use squirt bottle) of the solution onto the regulator/canister connections. • Inspect the connections and look for bubbles • If NO bubbles appear, the connection is safe. • If bubbles appear, there is a leak: • Loosen and re-tighten this connection. • Re-check for a leak. • If you continue to see bubbles after several attempts, disconnect propane source and contact 1-800-762-1142. 7 Owner’s manual and assembly instructions: 71400 portable outdoor heater 3/3/03 Contact 1-800-762-1142 for assistance. Do not return to place of purchase. Endless Summer Step 6 - Install Access Panel • Rotate door up to closed position and tighten thumb screw Step 7 - Securing the Tank Mount your 20 lb. cylinder to a sturdy object such as a table or post within 3 to 4 feet of your heater when in use, this will prevent movement or tipping of the cylinder during operation. The clamp on the cylinder ring will attach to any round pole from 1” to 2” in diameter, or a square post from 1” to 2” square. It will also adapt to various other shapes up to 2” wide. Determine where to locate your 20 lb. cylinder. Be sure that it is within 2” what you are mounting it to. Place the bracket halves around the object and insert the 2” bolts through the open holes in one bracket and into the matching threaded h...