This feature is usually associated with extended run models. Unpacking When unpacking, inspect carefully for any damage that may have occurred during transit. Make sure any loose fittings, bolts, etc., are tightened before putting unit into service. General Safety 1. Before starting or servicing any generator, read and understand all instructions. Failure MANUAL to follow safety precautions or instructions can cause equipment damage and or serious personal injury. Engine instructions for these u

Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. Generators TM BUILT TO LAST These generators are powered by air- cooled four cycle engines and designed to run at maximum RPM and give a continuous wattage as rated. When unpacking, inspect carefully for

9. WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: A. Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts. B. If the purchaser does not receive satisfactory results from the Authorized Service Center, the purchaser should contact Campbell Hausfeld (see paragraph 2). Limited Warranty applies in the U.S. and Canada only and gives you specific legal rights. You

E. Items or service that are normally required to maintain the product, i.e. lubricants and filters. F. Gasoline engine components are expressly excluded from coverage under this limited warranty. Such components should be returned by the purchaser to the original manufacturer or to its authorized repair stations for service. 7. RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, generator or component(s) which have failed within duration of the warranty

Long power cords and extension cords draw additional power. Keep cords at minimum possible length. Installation for Stand-by Use Precautions must be taken to prevent electrical back feeding into utility systems. This requires isolation of the electrical system. To isolate the electrical system, perform the following procedures: 1. Turn off the main electrical system switch prior to connecting the generator. 2. In accordance with national and local standards, a double throw transfer switch must b

3. Total combined load through any combination of receptacle must not exceed the rated load limits of the generator. NOTE: Power draw can be calculated by multiplying volts and amps. The resulting number is wattage. Never exceed the posted maximum wattage for the generator or any individual receptacle. Refer to owner's manuals and product tags to determine the wattage of electrical load devices. Long power cords and extension cords draw additional power. Keep cords at minimum possible length. Ma

Set the switch to the ON position. 5 600 1200 500 300 200 125 4. Move the choke/run switch to the 7.5 900 1800 350 200 125 100 choke position. 10 1200 2400 250 150 100 50 5. Pull the starter rope with a brisk 15 1800 3600 150 100 65 smooth motion. 20 2400 4800 175 125 75 50 6. Move the choke/run switch to the run position. 7. After each start up, allow engine to run 2-3 minutes with no load. Engine speed is ! CAUTION preset to provide proper output voltage. Never attempt to modify or adjust engi

Make sure any loose fittings, bolts, etc., are tightened before putting unit into service. 1. Before starting or servicing any generator, read and understand all instructions. Failure to follow safety precautions or instructions can cause equipment damage and/or serious MANUAL Description Unpacking General Safety personal injury. Engine instructions for these units are contained in a separate manual. Retain all manuals for future reference. 2. Never use this generator for any application other t

Never attempt to modify or adjust engine speed or output voltage. GENERATOR SHUT OFF 1. Remove all electrical load devices from the generator. 2. Allow the engine to run for 2-3 minutes with no electrical loads. 3. Set the switch to the OFF position. This will stall the engine. 4. Verify that the generator has completely stopped. 5. Allow the unit to cool before installing any covers. LOAD DEVICES 1. The 120 volt receptacles are rated for 15 amps. The 120V twist lock receptacle is rated for 30 a

Make sure any loose fittings, bolts, etc., are tightened before putting unit into service. General Safety 1. Before starting or servicing any generator, read and understand all instructions. Failure MANUAL to follow safety precautions or instructions can cause equipment damage and/or serious personal injury. Engine instructions for these units are contained in a separate manual. Retain all manuals for future reference. 2. Never use this generator for any application other than that specified by