Tighten securely. BAGGER KIT INSTALLATION STEP 11: Install bumper mount standoffs onto rear bumper of machine, utilizing existing hardware on machine. NOTE: Invert hardware when installing standoffs, installing bolts out through bumper with nuts facing out. NOTE: When installing standoffs, be sure that the bumper mount plate mounting holes along the back bar of the standoffs are located towards the right side of the machine. Refer to the Parts List section of the manual. STEP 12: Install bumper

3. Remove accumulated debris from the hydro fan cooling guards. Clean Debris From Machine Service Interval: Before each use or daily 1. Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake. 2. Clean off any oil, debris, or grass build-up on the machine and cutting deck, especially under deck belt shields, around the fuel tank, around engine and exhaust area. Clean Grass Build-Up UnderDeck Service Interval: Before each use or daily 1. Stop engine, wait for all movi

Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic failure with possible injury or death. BOLT TORQUE Mounting procedures for mowers will require a significant amount of bolt nut and washer installation. Frame and structure mounting bolts should be installed using Red Loct

(SRM-1) 12.3 Engaging the Power Take Off (PTO) Before engaging the PTO, make certain that the area is clear of bystanders and passersby. The implement must be completely lowered and the deck positioned at a safe operating height. NEVER engage the PTO with the implement in the raised position. Set the tractor engine speed at approximately 1,000 RPM before engaging the PTO. Shift the PTO control to the on position, and slowly increase the engine speed until the PTO is operating at the rated speed.

(Figure ASM-R-0151) ASSEMBLY © 2006 Alamo Group Inc. ASSEMBLY A96B 03/06 Assembly Section 3-13 CHAIN GUARD (EXTRA EQUIPMENT) CHAIN GUARDS: Front and Rear Chain Guards (Optional Equipment) are recommended for higher than normal usage (100 hours or more per year) and will provide protection from thrown objects with careful operation. Chain Guards must be maintained in good repair by replacing missing or worn sections or by being replaced when seriously worn or damaged. Front Chain Guards 1. Attach

OPS-R-0004_F OPERATION © 2009 Alamo Group Inc. OPERATION RX60/72/84 03/09 Operation Section 4-19 Shorten the driveline profiles as follows: • Remove the driveline from the tractor. • Raise and lower the mower to find the position with the shortest distance between the tractor PTO shaft and cutter gearbox. Shut down the tractor and securely block the mower in this position. • Pull driveline apart and reattach yoke to PTO shaft. • Hold driveline sections parallel to one another and measure back 1”

1/98 Printed in USA onriens Thank You Ariens outdoor power equipment is engineered to bé the best from start to finish. We have one fundamental belief . Value is not measured solely, by price;. . . value Js a durable, easy-to-use machine . that performs season after season. This manual and the engine manual aré your, guidés, By-foHowing thèinstructions and procedures in them, your Ariens equipment will serve you well for many years: The care you give this unit will . determine your overall

ALWAYS wear safety glasses and protective gear near battery. DO NOT TIP battery beyond a 45° angle in any direction. ALWAYS keep batteries out of reach of children. Hydraulics HYDRAULIC FLUID WILL CAUSE SEVERE BURNS. Fluid in the hydraulic system can penetrate the skin and cause death or serious injury. Cleaning Keep unit free of grass, leaves, or other debris. Clean up oil or fuel spills. Storage For unit storage or extended storage: • NEVER store with fuel in fuel tank, inside a build

Order P/N: 00036800 - Three pack of 3 oz. cartridges or 00036700 - Ten pack of 14 oz. cartridges. Figure 9 OE0031 OE0192 16 Aliens« EZRider™ Orig. 1/98 Tire Pressure Battery Before each use, make a visual check of tires. The correct air pressure is 10-12 psi (65-83 kN/m2). Hydraulics and Transaxles HYDRAULIC FLUID WILL CAUSE SEVERE BURNS. Fluid in the hydraulic system can penetrate the skin and cause serious injury or death. Keep body and hands away from pin holes or nozzles which exp