Pred zacatim prace si prosim dokladne precitajte navod na obsluhu a tento si aj pre pripad potreby uschovajte SI Garancija ne velja ob nepravilni uporabi proizvoda in/ali ob uporabi za drugi namen kot je izdelan. Prosimo, da pred uporabo, preverite pazljivo navodila za obratovanje in jih shranite za kasnejso rabo. HU Jotallast vallalni csak rendeltetesszeruen hasznalatba vett gepekre tudunk. Kerjuk, hogy a gep hasznalatba vetele elott gondosan olvassa el a kezelesi utasitasokat. PL Gwarancja tra

• ........................... • ................................................ • ........................... • ........................... • NL SERVICE AANTEKENINGEN Vul telkens u service uitvoert, de datum in Indien nodig om de 8 uur om de 25 uur om de 50 uur om de 100 uur om de 200 uur Motorolie vervangen ......................... Draaipunten smeren ......................... Werking van de remmen controleren Lchtscherm schoonmaken ................ Luchtfilter en voor-reiniger schoonmaken ...

36 This product has a low emission engine which operates differently from previously built engines. Before you start the engine, read and understand this Owner's Manual. IMPORTANT: For answers to your questions about this product, Call: Read and follow all Safety 1-800-659-5917 Rules and Instructions before Sears Craftsman Help Line operating this equipment. 5am -5pm,Mon -Sat SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179 U.S.A. Visit our C raftsman webs ite:www,sears,com/crafts man 'As rated

The BEST method of handling the ground speed control levers is in three steps -as shown in Figure 7. FIRST place your hands onto the levers as shown. SECOND, to go forward gradually push the levers forward with your palms. THIRD, to speed up move the levers farther forward. To slow down smoothly, slowly move the levers back toward neutral. Figure 7. Move Control Levers Gradually Forward Travel Practice Gradually move both ground speed control levers evenly FORWARD from neutral (see Figure 8). Sl

Tighten securely. Slide terminal cover (C) over terminal. 5. Connect BLACKgrounding cableto negative (-) battery terminal with remaining hex bolt and keps nut. Tighten securely. 6. Close hood. ( _ Negative(Black) Cable Positive (Red) Cable A TO REPLACE HEADLIGHT BULB 1. Raise hood. 2. Remove bulb holder from the hole in the backside of the grill. 3. Replace bulb in holder and install bulb holder securely back into the hole in the backside of the grill. 4. Close hood. INTERLOCKS AND RELAYS Loose

Avoid contact with skin and eyes. Explosion hazard. Changing the battery produces explosive hydrogen gas. Only charge the battery in a well ventilated area, away from any ignition source such as a water heater, electric motor, or a lit cigarette. Wear Protective Equipment Always wear gloves and safety glasses when handling the battery and battery cables. Service Interval: 100 Hours . Disconnect the cables from the battery, negative cable first (B, Figure 27). 2. Remove the rubber strap securing

1 YEAR LIMITED WARRANTY ON MODEL 291.376100 SEARS LAWN MOWER For one year from the date of purchase, when this Sears Lawn Mower is maintained and lubricated according to the instructions in the owner's manual, Sears will repair, free of charge, any defect in material aud workmanship. This warranty does not cover: Expendable items which become worn during normal use. Repairs necessary because of operator abuse or negligence, and the failure to maintain the equipment according to the instructions

• As you followthe instructionsbelow,refer to Figure 1 for more information. • Thecuttingbarblade(locatedunderthe reel)pivots.Thefrontscrewsmovethe cutterbarawayfromtheblades,while therearscrewsmovethe cuttingbartowardthe blades. • Adjustingthe screws is a very sensitive procedure. 1116thof a turn is considered a major adjustment, • Beforetightening one adjusting screw,be sureto loosenthe opposingscrew an equal amount. LOOSENING THE BLADES • Thecutterbarblade mustbe movedfurtherfromthecuttingree

7. Do not mow the lawn when it is wet enough to be slippery. 8. Always be sura of your footing. Walk, don't run. 9. Keep all screws and nuts tight. Be sure equipment is in a safe operating condition. Keep mower clean of dry grass and dirt. REGLAS DE OPERACI(_N SEGURA 1. Lea y familiaricese con las formas de uso. 2. Inspeccione su cSsped y retire cualquier objeto extra,o, etc. 3. No opere la podadora descalzo o usando sandatias. 4. Tenga cuidado. Una podadora es un aparato de precision para el cu

• Misalignment can occur resulting in blades that are too loose or too tight. If this happens, you will notice a rough, uneven cut or a hard pushing mower. • All adjustments are made from the rear of the mower (opposite from the bar with the logo decal.) Each end of the cutting bar can be adjusted separately. • As you follow the instructions below, refer to Figure 1 for more information. • The cutting bar blade (located under the reel) pivots. The front screws move the cutter bar away from the b