3. DRIVE ShAFT ASSEMBLy - Contains a specially designed liner and the flexible drive shaft. 4. WhEEL - Adjustable up/down, sets depth of blade. A B D Parts Required: PAS or SRM-SB Power Head w/Shaft & Coupling. 1. Set Power Head/Shaft Assembly on a level surface. 2. Pull locator pin (A) out, and turn counter-clockwise 1/4 turn to lock-out position. 3. Remove vinyl cap from attachment drive shaft. 4. Remove cardboard spacer, if necessary. 5. Carefully fit attachment drive shaft assembly into coup

Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts. assembly wArningDo not perform maintenance or assembly procdures with engine running. Tools Required: 4 & 5 mm Hex Wrench Parts Required: ProSweep Gear Housing, Lower Drive Shaft Assembly, PAS or SRM-SB Power Head w/Shaft & Coupling. prosweep gear housIng assembly to lower drIve shaft assembly 1. Remove vinyl caps from attachment drive shaft. 2. Place brush gear housing

Pilot must match blade center hole for proper fit. 2. Place blade (E) over upper plate pilot and install the "lower plate" (F) and L.H. nut (G). Tri-Cut blade (H) is installed with glide cup (J). 3. Insert locking tool (K) through hole in upper plate and notch in gear housing (C) to prevent splined shaft from turning, tighten nut (G) and secure with a split pin (L). C A B H K D E J F G L K D 20 2020202020 E F G L IMPORTANT Never reuse a cotter pin - install a new cotter pin each time a blade is

NOTE Use of a harness (not included) and this kit will allow use of metal or nylon grass/weed blades. All other metal blade usage requires a "U" Handle Kit and restrictive harness. NOTE The Barrier Bar is used to restrict rearward movement of the unit. For heavy-duty or extended use, U-handles should be used. See your Echo dealer or Trimmer/Brush Cutter Safety Manual for details regarding U-Handles. If you have additional questions, contact your Echo Service Dealer, or call Echo directly at 1-80

d. Tighten harness clamp screw. INSTALL SHIELD AND GEAR HOUSING ASSEMBLY 1. Push gearbox assembly on end of drive shaft taking care to engage the drive cable with the gear housing. 2. Locate the gear housing on the drive shaft and install the locating screw (B). 3. Tighten the two (2) side clamping screws (A). INSTALL HANDLE/BARRIER BAR A A B NOTE The Barrier Bar is required when using blades. Units equipped with U-Handles do not require installation of the Barrier Bar. 1. Position front handle

CONTENIDO: 1, Soporte 1, Placa superior, 20 mm 3, Tornillos de 5 x 15 mm (montaje en el protector) 1, Placa inferior 2, Tornillos 5 x 8 mm (soporte al protector) 1, Abrazadera del arnes con espaciador 4, Tuerca de 5 mm 1, Anillo del arnes 4, Arandelas de traba 5 mm 1, Barrera de barra 1, Perno de 5 mm x 18 mm (Abrazadera del arnes) 1, Protector de metal 1, Tuerca de M10 x 1.25 L.H. INSTALE EL PROTECTOR DE METAL Si es necesario, quite la cabeza de nilon, el protector de plastico y la placa superi

Handling Fuel warning Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury may result. • Use an approved fuel container. • DO NOT smoke near fuel. • DO NOT allow flames or sparks near fuel. • Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize. • NEVER refuel a unit when the engine is HOT or RUNNING! • DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground. • DO NOT overfill

. ALWAYS fill fuel tanks outdoors over bare ground. • Securely tighten fuel cap after refueling. • Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired. IMPORTANT Spilled fuel is a leading cause of hydrocarbon emissions. Some states may require the use of automatic fuel shut-off containers to reduce fuel spillage. Contact your ECHO dealer for ordering information. After refueling • Wipe any spilled fuel from the unit. • Move at least 3

4. Loosen adjustment knob and adjust the blade's depth of cut toproduce a fine cut between sidewalk and grass using a minimumblade depth, usually with about 13 mm (1/2 in.) of the blade intothe ground. Tighten adjustment knob. 5. Before edging, plan your direction of travel so that the unit will always be positioned on your right side and so that you walk on a hard surface whenever possible. 6. Hold edger as shown. warningBefore edging, be sure to read and understand the entire Operator's Manual