Votes - 3, Average rating: 4.3 ( )

Manafacture: Cub Cadet File size: 8.1 mb File name: Language of manual:

This oil may be used for the first 30 hours of engine operation at temperatures between +90 degrees F. and 0 degrees F. If temperatures are not within this range, drain the oil from the crankcase and replace with new oil as specified in the "Lubrication Table". The engine oil must be drained and replaced with new oil every 30 hours of engine operation. We recommend I.H. No. 1® Engine Oil. If other than I.H. No. 1® Engine Oil is used, it must be designated "For Service MS". In new API Code these oils are usually designated as meeting either SD or SE requirements. To aid starting, the selection of crankcase lubricating oils should be based on the lowest anticipated temperature until the next drain period. See page Lubricate the entire tractor, using only high quality lubricating oils and greases as specified in the "Lubrication Table". For your own protection, select only oils and greases of recognized manufacture. Regularly check the oil levels of the engine crankcase and transmission to see that they are filled to the correct levels. NOTE: Check the oil level only while the engine is stopped. NOTE: On the Cub Cadet 86 Tractor the oil filler cap has the oil level gauge attached and is located on the right side of the tractor. NOTE: On all other models the oil filler cap and gauge is located on the gear cover on the left side Always keep the oil level between the "FULL" and the "LOW" marks on the gauge. When checking the oil level the gauge must be withdrawn and wiped clean, then inserted all the way and with- 33 LUBRICATION ENGINE OIL — Continued 1. Oil filler cap and oil level gauge - Cub Cadet 86 Tractor 1. Oil filler cap and oil level gauge - All models except the Cub Cadet 86 Tractor Keep your supply of lubricating oil absolutely clean and free from dust. Always use clean containers. Keep the lubricator clean and wipe dirt from the lubrication fittings before applying the lubricator. TRANSMISSION OIL FILTER (International Cub Cadet 129, 149, and Remove the throw-away can-type filter and replace with a new filter after the first 10 hours and after 50 hours of operation, and every 100 hours of operation thereafter. NOTE: Clean the outside area before removing the filter to keep dirt from getting into the transmission case. If a mower is mounted on the tractor, the mower must be lowered to facilitate removal of the filter. To remove the filter, turn the filter counterclockwise using an automotive type filter wrench or an open end wrench. Before installing the new filter, apply a coating of oil on the filter gasket. Thread the filter on by hand until tight enough to seat the gasket. Loosen the filter. Then turn it until the gasket contacts the base. Tighten the filter an additional one half turn. Check for leaks and check oil level of transmission case. 34 LUBRICATION TABLE Point of Lubrication Check at Hours Change at Hours Capacity Anticipated Air Temperature Above+32°F. +32°F. to 0°F. Below 0°F. Engine Crankcase Model 86 Tractor 10 30 2-1/2 pt. I.H. No. 1® Engine Oil SAE-30 Note: Do not substitute 10W-30 or 10W-40 I.H. No. 1® Engine Oil SAE-10W I.H. No. 1® Engine Oil SAE-5W-20 or SAE-5W Engine Oil Engine Crankcase Models 108, 128, 129, 149, and 169 Tractors 10 30 3 pt. T ransmission Models 129, 149, and 169 Tractors 100 Add as needed 14 pt. IH Hy-Tran® Fluid If fluid is used which does not meet requirements of IH B-6 Specification, International Harvester Company will not be responsible for substandard performance of transmission and hydraulic components. NOTE: Failures due to use of improper fluid or filters are not covered by warranty.—FOR MAXIMUM PROTECTION USE IH HY-TRAN® FLUID AND FILTERS. Transmission Models 86, 108, and 128 Tractors 100 Add as needed 7 pt. Approx. Creeper drive housing Models 86,108, and 128 Tractors 100 Add as needed 1/2 pt. Steering gear housing All models Yearly — 1/4 lb. Two strokes of the lubricator using IH-251H EP grease or equivalent #2 multi-purpose lithium grease. Steering knuckles All models 10 Use IH-251 IH EP grease or equivalent #2 multi-purpose lithium grease and apply two or three strokes of the lubricator or sufficient grease to flush out old grease and dirt. 35 LUBRICATION GUIDE International Cub Cadet 86,108 and 128 Tractors 36 Lubrication view LUBRICATION GUIDE International Cub Cadets 86,108 and 128 Tractors — After Every 10 Hours of Operation 1 - Oil filler cap and bayonet-type oil level gauge. Cub Cadet 86. 1A - Oil filler cap and bayonet-type oil level gauge for Cub Cadet 108 Check the oil (with the engine stopped) and add sufficient new oil to bring it to the "FULL" mark on the gauge. Do not overfill. Do not operate the engine if the oil level is below the "LOW" mark on the gauge. 2 - Steering knuckles (2). 3 - Front axle pivot pin. 4 - Engine crankcase. ♦ 5 - Power take-off shafting bearing. Use IH 251H EP grease or equivalent #2 multi-purpose lithium grease and apply sufficient grease to...

Download now

Please, enter two numbers from picture: