Votes - 3, Average rating: 4 ( )

Manafacture: Frymaster File size: 1.46 mb File name: Language of manual:

Then allow it to cool to the touch. 3. Place a large metal container under the drain valve. WARNING Do not use a plastic container. If the water is not cool enough, the container will melt, possibly causing you to be burned, and causing cleaning solution to get on the floor. 4. Open the drain valve and allow the water to drain into the container. 5. Watch the container to make sure the water does not overflow the container. If the container becomes full, close the drain valve, put another large metal container under the drain valve, and open the drain valve again. WARNING Do not allow the water to overflow the container. Water will get on the floor, and if the water is not cool enough, you may be burned. 6. When the draining is complete, close the drain valve. 7. Carefully carry the container(s) to the sink and slowly pour the water into the sink. WARNING Thoroughly clean and dry the floor if water is spilled. Water on the floor can cause serious injury or loss of life. Drying Dry the inside of the kettle thoroughly, using a soft cloth. WARNING Dry the kettle thoroughly. Moisture causes hot shortening to spatter, which may cause serious injury. Belshaw Bros., Inc. .. 1750 22nd Ave. S. .. Seattle, WA 98144 .. Phone 206-322-5474 .. Fax 206-322 MN-1126EN 618L, 624, and 634 Electric Fryers Troubleshooting 4 If you have a problem with your fryer that you cannot solve, call your dealer or another qualified technician. If your dealer cannot help you, please call Belshaw Bros. at (206)322-5474. When you call, please specify the following: . The model name of the machine. . The serial number of the machine. . The voltage, phase, and cycle of the machine. CAUTION If you perform repairs yourself or have them performed by anyone other than a service technician authorized by Belshaw Bros., you do so at your own risk. WARNING Disconnect the machine from the power source before disassembling, repairing, or wiring. Belshaw Bros., Inc. .. 1750 22nd Ave. S. .. Seattle, WA 98144 .. Phone 206-322-5474 .. Fax 206-322 618L, 624, and 634 Electric Fryers MN-1126EN THE FRYER WILL NOT TURN ON OR HEAT Possible Causes What To Do The on/off switch is not in the ON position. Move the on/off switch to the ON position. The on/off switch is located inside the fryer cabinet, on the right hand side. The thermostat is not turned on. Turn the thermostat knob to a setting that is high enough to make the “Heating” pilot light come on. The high-temperature limit control switch has been tripped. Press the red reset button on the back of the heater head. WARNING Before doing any of the following, turn off the machine and allow the shortening to cool. The primary power distribution circuit breaker has been tripped. Flip the circuit breaker. The circuit breaker is visible through an access cutout in the electrical box. (The electrical box is inside the cabinet, in the back.) A fuse is blown. Replace the fuse. THE HEATING ELEMENTS FAIL TO MAINTAIN THE PROPER TEMPERATURE Possible Causes What To Do WARNING Before doing any of the following, turn off the machine and allow the shortening to cool. The thermostat is out of adjustment. Re-calibrate the thermostat. See Appendix B, “Electrical Components.” The thermostat is defective. Replace the thermostat. Sediment has accumulated around the thermostat bulb. Remove the shortening from the fryer, as explained in Section 3, “Cleaning.” Remove the sediment from the thermostat bulb. Belshaw Bros., Inc. .. 1750 22nd Ave. S. .. Seattle, WA 98144 .. Phone 206-322-5474 .. Fax 206-322 MN-1126EN 618L, 624, and 634 Electric Fryers THE HEATING ELEMENTS WILL NOT HEAT Possible Causes What To Do The fryer’s circuit breaker has been tripped. Press the red reset button on the back of the heater head. The high-temperature limit control switch has been tripped. Press the red reset button on the back of the heater head. WARNING Before doing any of the following, turn off the machine and allow the shortening to cool. The contactor is defective. Replace the contactor. A heating element is defective. Replace the defective heating element. The high-temperature limit control is defective. Replace the high-temperature limit control. The thermostat is out of adjustment. Re-calibrate the thermostat. See Appendix B, “Electrical Components.” The thermostat is defective. Replace the thermostat. Belshaw Bros., Inc. .. 1750 22nd Ave. S. .. Seattle, WA 98144 .. Phone 206-322-5474 .. Fax 206-322 618L, 624, and 634 Electric Fryers MN-1126EN Appendixes A Donut-Making Helps B Electrical Components C Parts Lists D Wiring Diagram E Limited Warranty Belshaw Bros., Inc. .. 1750 22nd Ave. S. .. Seattle, WA 98144 .. Phone 206-322-5474 .. Fax 206-322 MN-1126EN 618L, 624, and 634 Electric Fryers A Donut-Making Helps Tips on Making Quality Cake Donuts . Use the correct batter temperature. In general, the correct batter temperature is 75. -80. F/24. -27. C. Check the mix manufacturer’s instructions, as the recommended temperature range may vary. If the ba...

Download now

Please, enter two numbers from picture: