Votes - 3, Average rating: 3.3 ( )

Manafacture: GE File size: 1.42 mb File name: Language of manual:

It should be minimum T WC natural gas or 12" WC LP gas. If gas pressure is correct replace defective gas control valve. 3. in an operating situation and with control thermostat set at #10. does the operating (upper) pilot fight go out too early? (Burners shut off too early) Yes No Go to step # 4. Go to step # 2. 4. Immediately after operating (upper) pilot goes out turn control thermostat to #1. Can you hear or feel the thermostat “clicking" off? Yes No. Adjust or replace safety thermostat (adjust to 470°F) Adjust or replace control thermostat (adjust to approx. 425°F) C/Problem: Skillet is overheating. Replace or adjust control thermostat (adjust to approx. 425°F) Verify that the safety thermostat shuts off at approx 470°F. D/Problem: Skillet fails to tilt (Power tilt units) (Note: A thermal overload in jack motor does not allow constant consecutive tilting) Possible Causes 1. No electrical power to the skillet 2. Defective rocker (up-down) switch. 3. Defective start capacitor. 4. Blown 10 amp fuse. (208-240V units) 5. Defective 208-240/120 VAC transformer. (208-240V units) 6. Defective power jack. Fault isolation Procedure Step Test Result Remedy 1. Is there electrical power to the skillet? Yes Go to step #2. No Correct external power supply problem. 2. On 120V units, go to step #4. On 208-240V units, is either one of the 10 amp fuses blown? Yes No Replace biown fuse. Go to step # 3. 3. is there 120 VAC present at output of 208-240/120 VAC transformer? Yes No Go to step #4. Replace defective 208-240/120 VAC transformer. 4. Test rocker switch for continuity. Is it operating properly? Yes No Go to step # 5. Replace defective rocker switch. 5. Remove motor from power jack. Activate tilt switch. Does the motor rotate? Yes No Replace defective power jack. Go to step # 6. 6. Remove power jack wiring from connections. Measure resistance across each of the three wires. Do they read (approx) 14 ohms between black and white. 29 ohms between black and red. and 14 ohms between red and white? Yes No Replace defective start capacitor. Replace defective motor. GAS PRESSURE ADJUSTMENT PROCEDURE CAUTION: Hie following procedure, as well as other work on gas controls should be performed only by a qualified service technician. NOTE: Gas pressure adjustment is pre-set and rarely needs any adjustment 1. Remove gas pressure adjustment cover screw. 2. Operating gas pressure output shouid be regulated to 6"W.C. natural gas and 11 "W.C. LP gas. 3- Turn gas pressure adjustment screw (under cover screw) clockwise to increase or counterclockwise to decrease gas pressure. 4. Replace cover screw. PILOT FLAME ADJUSTMENT PROCEDURE CAUTION: The following procedure, as well as all other work on gas controls should be performed only by a qualified service technician. 1. Remove pilot adjustment cover screw. 2. Tum pilot flow adjustment screw (under cover screw) clockwise to increase flame (see below drawing for correct flame adjustment). 3. Replace cover screw. COraMCnON COmROLWUfE PBJOTGSSUOOR HYDRAULIC JACK REPLACEMENT PROCEDURE Refer to "Hydraulic Jack Assembly” drawing. 1. Place skillet pan in a down position. 2. Remove jack’s top mounting pin (1). 3. Remove micro switch bracket (25) by removing screws (24). 4. Insert a #10-24 screw or bolt into jack’s bottom mounting pin (20) and pull pin away from jack to remove. 5. Disconnect hydraulic hose (28,29) at connector (30). 6. Remove jack from skillet 7. Disconnect hydraulic ho...

Download now

Please, enter two numbers from picture: