Votes - 0, Average rating: 0
(
)
)
|
Other manuals for this model:
manual abstract
Be sure to use a cloth free of salt residue that doesn’t leave any loose fibers. Dry the Case completely at a well ventilated location in the shade. CAUTION: • Do not use hot air from a hair dryer or the like for drying and do not expose the Case to direct sunlight, as this may accelerate deterioration and deformation of the Case and deterioration of the O-ring, leading to leakage of water. • When wiping the Case, take care not to cause scratches. EN 22 6. Maintaining the Waterproof Function Whenever you open the rear lid of the Case, always be sure to perform the O-ring maintenance operation as described below. Perform at the location without sand or dust, after washing and drying your EN hands. Remove the O-ring 1 Insert the O-ring remover between the O-ring and the O-ring groove. 2 Slip the tip of the inserted O-ring remover below the O-ring. (Be careful not to scratch the O-ring groove with the tip of the O-ring remover.) 3 Hold the O-ring with your fingertips after it has come out of the groove and remove it from the Case. Remove any sand, dirt, etc. After visually checking that dirt has been removed from the O-ring, checks for sand and other foreign matter adhered, damage and cracks can be done by squeezing the entire circumference of the O-ring lightly with your fingertips. EN 23 Remove any foreign matter adhered to the O-ring groove using a lint-free clean cloth or cotton swab. Also remove any sand or dirt adhered to the O-ring contact surface on the front lid of the case. EN CAUTION: • Maintenance of the waterproof functions is required even before using this product underwater for the first time. • When a sharp object is used to remove the O-ring or to clean the inside of the O-ring groove, the Case and the O-ring may be damaged and water leakage may occur. • Take care not to stretch the O-ring. • Never use alcohol, thinner, benzene or similar solvents or chemical detergents to clean the O-ring. When such chemicals are used, the O-ring may be damaged or its deterioration will be accelerated. EN 24 How to Apply Grease to the O-ring 1 Apply the exclusive lubricant to each O-ring. Make sure that your fingers and the O-ring are free of dirt, and squeeze about 5 mm of lubricant onto a finger. (5 mm is the most appropriate amount.) 2 Spread the lubricant all over the O-ring. Apply the lubricant with three fingers and spread it over the ring. Be careful not to use force as this may stretch the O-ring. 3 Check that the O-ring is free of scratches or unevenness. After spreading the lubricant, check visually and by touch that the O-ring is not scratched and that its surface is flat. If it is damaged in any way, be sure to replace it with a brand-new O-ring. 4 Apply lubricant on the O-ring contact surface. Use the lubricant remaining on the fingers to clean and lubricate the case’s contact surface. EN CAUTION: • Always perform maintenance of the waterproof function even when the Case has been opened every shooting. Neglecting this maintenance may cause water leakage. • When the Case is not to be used for a long time, remove the O-ring from the groove to prevent deformation of the O-ring, apply a thin coat of silicone grease, and store it in a clean plastic bag or the like. EN 25 Install the O-ring EN Confirm that no foreign matter is adhered, apply a thin coat of the grease provided to the O-ring, and fit the O-ring into the groove. At this point, confirm that the O-ring does not stick out from the groove. When sealing this product, make sure that no hairs, fibers, sand particles or other foreign matter stick not only to the O-ring, but also to the contact surface (front cover). Even a single hair or a single grain of sand may cause water leakage. Please check with special care. Examples of foreign matter sticking to the O-ring Hair Fibers Grains of sand Replace consumable parts • The O-ring is a consumable part. Regardless of the number of times the Case is used, it is recommended that the O-ring be replaced with a new one at least once a year. • Deterioration of the O-ring is accelerated by the use conditions and the storage conditions. Replace the O-ring even before a year has passed if it shows signs of damage, crack or loss of elasticity. Note: • Please use genuine Olympus silicone grease, silica gel and O-ring. • Do not try to replace the O-ring by yourself. • We recommend to perform the check periodically. EN 26 7. Appendix Specifications EN Compatible models Olympus digital camera STYLUS TG-830 Pressure resistance Depth of up to 45 m Main materials Body: Polycarbonate Lens window: Multiple coat glass Diameter of lens ring .52 mm Operating environment 0 °C - 40°C (32 °F - 104 °F) (operation) / –20 °C - 60 °C (–4 °F - 140 °F) (storage) Dimensions Approx. 153 mm (Width) x 118 mm (Height) x 75 mm (Depth) Weight Approx. 435 g (camera and accessories not included) Weight under water Approx. –200 g (in the freshwater) (Underwater case only) * We reserve the right to change the external appearance and the sp...
Other models in this manual:Cameras & Photo - PT‑055 (1.71 mb)