Login:
Votes - 5, Average rating: 4.2 ( )

User manual Kenwood, model KCA-R42FM

Manafacture: Kenwood
File size: 250.85 kb
File name:
Language of manual:en
Free link for this manual available at the bottom of the page



Other manuals for this model:

manual abstract


• This function is not available when the random play, repeat or scan play function is on. Before using this function, cancell the other functions. This function cannot be used while loading a disc (while the play indicator is blinking). 2 To change the frequency Press the 4 or . button on the display unit. The transmission frequency will change as follows : ¤¤¤¤¤¤ ¤¤¤¤¤¤ 87.7MHz 89.9MHz 87.9MHz 89.7MHz 88.1MHz 89.5MHz 88.3MHz (initial value) 89.3MHz 88.5MHz 89.1MHz 88.7MHz 88.9MHz ¤¤ ¤ ¤¤ ¤ ¤¤¤ ¤¤ ¤ — 9— External disc control features English Modulation 1 To set the control mode Hold down the RDM button three seconds. The LEVEL indicator will light modulation level will be displayed. Modulation level NOTE Dynamic control The unit comes with reduce sound distortion. If the sound is distorted + button on the display unit and then set the If the prevention of distortion function extension is reduced. The initial setting is "1" (OFF). LEVEL Number for prevention of distortion setting NOTE • If this function is on, the functions other than power on reset, and changing the transmission frequency, cannot be operated. • This function is not available when the random play, repeat play, or scan play function is on. Before using this function, cancell the other functions. This function cannot be used while loading a disc (while the play indicator is blinking). 2 To change the modulation level Press the 4 or . button on the display unit. . Each time the 4 or . button is pressed, the modulation level changes in the range from 1 to 4. As the number increases, the modulation level increases.The initial setting is 2. 2 CAUTION If a disc with a high recording level is used, distort even if the prevention of distortion (ON). In this case, reduce the modulation level. To cancell : Hold down the RDM button on the display unit for three seconds. The LEVEL indicator will go off and the modulation level change will take effect. The control mode is automatically cancelled if you do nothing for 15 seconds. — 10 — — 11 — Accessories External view ......... Number of items .........1 2 .........2 1 The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. 2CAUTION .........1 3 .........1 4 .........1 5 1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. 2. Make the proper input and output cable connections for each unit. 3. Connect the wiring harness cables in the following order: ground, battery, ignition. 4. Install the unit in your car. 5. Reconnect the - battery. 6. Press the reset button. When drilling a hole in the car chassis to install the unit, check first that nothing is on the other side. • If the fuse blows, first make sure the cables aren’t touching to cause a short circuit, then replace the old fuse with one with the same rating. • Do not let unconnected cables or terminals touch metal on the car or anything else conducting electricity. To prevent a short circuit, do not remove the caps on the ends of the unconnected cables or the terminals. • After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. • Insulate unconnected cables with vinyl tape or other similar material. • Some disc changers need conversion cords for connection. See the section on "Safety Precautions" for details. 2CAUTION 2WARNING Installation Procedure Conecting English Display unit Control output Changer connection cable Control input CD/MD auto - changer input FM modulator unit CD MD AUTO CHANGER CONTROLLER REP RDM 3 - + 4 . PWR M.RDM D.REP TRACK DISC 8/ D.SCN MHz DISC FREQ LEVEL 2 WARNING To prevent fire when the ignition cable (Red) or battery cable (Yellow) is short-circuited by coming into contact with the vehicle chassis (ground), only connect the power supply after making the fuse box connections. CD/MD auto-changer Output When the disc changer with the O-set the switch to "O" position to operate Battery NOTE Do not install an antenna of radio equipment or distribute the antenna cable near the changer output cable, for this could cause malfunction with this unit. FM/AM antenna input FM/AM antenna output Ground cable (Black) - (To car chassis) Car fuse box ACC Ignition key switch Antenna plug for automobile Car stereo with FM tuner Battery cable + (Yellow) Ignition cable + (Red) 4 5 2 CAUTION Be sure to press the reset button after installation. — 12 — Installation n Installation of Display unit • Installation without 3 Display unit Attach one velcro to slanted-line of the the units as shown above, and attach the other velcro to the parts where you wish to attach the display units. Then, put velcros together 2 and install the display units. • Installation using the trim mount plate 3 CD MD AUTO CHANGER CONTROLLER REP RDM 3 1 A PWR M.RDM D.REP D.SCN MHz TRACK DISC 8/ FREQ LEVEL - + DISC Display unit 3 Pass the cable from the display unit t...


Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category