Votes - 3, Average rating: 4 ( )

Manafacture: Kenwood File size: 424.22 kb File name: Language of manual:

— 4— About CDs About CDs s CD cleaning • Don’t touch the recording Clean from the center outward. • CD-R and CD-RW are easier to damage than a normal music CD. Use a CD-R or a CD-RW after reading the caution items on the package etc. • Don’t stick tape etc. on the CD. Also, don’t use a CD with tape stuck on it. When using a new CD If the CD center hole or outside rim has burrs, use it after removing them with a ball pen etc. Burrs Burrs CD accessories Don’t use disc type accessories. Removing CDs When removing CDs from this unit pull them out horizontally. CDs that can’t be used • CDs that aren’t round can’t be used. • CDs with coloring on the recording surface or that are dirty can’t be used. • Don’t use CDs without disc mark . • A CD-R or CD-RW that hasn’t been finalized can’t be played. (For the finalization process refer to your CD-R/CD-RW writing software, and your CD-R/CD-RW recorder instruction manual.) CD storage • Don’t place them in direct sunlight (On the seat or dashboard etc.) and where the temperature is high. • Store CDs in their cases. — 5— General General English Release button (KDC-4020/KDC-3020/KDC- AM FM . 4ud SRC ATT/ #1 #3 CLK/ Q/ LOUD ADJ AUD KDC-4020/KDC-3020/KDC-2020 ATT indicator LOUD indicator SYSTEM Q indicator Clock indicator ATT indicator LOUD indicator SYSTEM Q indicator KDC-1020/KDC-1020S Clock display Clock indicator Clock display Turning ON the Power Press the [SRC] button. Turning OFF the Power Press the [SRC] button for at Selecting the Source Press the [SRC] button. Source required Display Tuner "TUnE" CD "CD" External disc "DISC" (Function of the KDC-4020/KDC-3020/KDC-2020) Standby (Illumination only mode) "OFF" Volume Increasing Volume Press the [ u] button. Decreasing Volume Press the [ d] button. Attenuator Turning the volume down quickly. Press the [ATT] button. Each time the button is pressed the Attenuator turns ON or OFF. When it’s ON, the "ATT" indicator blinks. — 6— Loudness Loudness Compensating for Press the [LOUD] button Each time the button is pressed Loudness turns ON or OFF. When it’s ON, "LOUD" indicator is ON. System Q You can recall the best sound setting preset the music. 1 Select the source to set Press the [SRC] button. 2 Select the Sound type Press the [Q] button. Each time the button is pressed the sound setting switches. Sound setting Display Flat "SQ-1" Rock "SQ-2" Top 40 "SQ-3" Pops "SQ-4" Jazz "SQ-5" Easy "SQ-6" Scan of Flat — Easy "SCAn" • Each setting value is changed with the (page 8) . First, select the speaker type with the Speaker setting. • When the System Q setting is changed, the Bass, Middle, and Treble set in audio control replace the System Q values. 1 Select the source for Press the [SRC] button. 2 Enter Audio Control mode Press the [AUD] button for at 3 Select the Audio item for adjustment Press the [FM] or [AM] button. Each time the button is pressed the items switch as shown below. 4 Adjust the Audio item Press the [ 4] or [ . ] button. Adjustment Item Display Range Bass level "BAS" –8 — +8 Middle level "MID" –8 — +8 Treble level "TRE" –8 — +8 Balance "BL" Left 15 — Right 15 Fader "FD" Rear 15 — Front 15 5 Exit Audio Control mode Press the [AUD] button. — 7— General General English Speaker Setting Fine-tuning so that the speaker type. 1 Enter Standby Press the [SRC] button. Select the "OFF" display. 2 Enter Speaker Setting mode Press the [Q] button. 3 Select the Speaker type Press the [ 4] or [ . ] button. Each time the button is pressed the setting switches below. Speaker type Display 2 Enter clock adjustment Press the [CLK] button The clock display blinks. 3 Adjust the hours Press the [FM] or [AM] button. Adjust the minutes Press the [ 4] or [ . ] button. 4 Exit clock adjustment mode Press the [CLK] button. Function of the KDC-4020/KDC-3020/KDC-2020 DSI (Disabled System Indicator) OFF "SP-F" A red indicator will blink on the unit after the faceplate For the OEM speaker "SP-O" removed, warning potential thieves. For 6 & 6x9 in. speaker "SP-6" 1 Turn the power OFF For 5 & 4 in. speaker "SP-5" Press the [SRC] button for at least 1 second. 4 Exit Speaker Setting mode 2 Set the DSI Press the [Q] button. While pressing the [#1] and [#3] button, press the [SRC] button. Each time the step 1 and 2 operation is done the DSI turns ON or Clock Display OFF. Press the [CLK] button. Each time the button is pressed the clock display turns ON or Function of the KDC-4020/KDC-3020/KDC-2020 OFF. When it’s ON, the clock indicator is ON. Theft Deterrent Faceplate The faceplate of the unit can be detached and taken with you, helping to deter theft. Adjusting Clock Removing the Faceplate Press the Release button. 1 Select the clock display The faceplate is unlocked, allowing you to detach it. — 8— The faceplate is damaged by shocks its special storage case • Do not expose the faceplate or excessive heat or humidity. Also avoid places with too dust or the possibility of water Reattaching the Faceplate 1 Align the projections on the ...

Download now

Please, enter two numbers from picture: