Mark the locations of the four mounting holes and the conduit entrance location on the wall. (The conduit entrance is the proper hole diameter for 1/2 inch (13mm) conduit.) 4. Fasten the backplate to the wall where previously marked. RECOMMENDATION: Wood wall - No. 16 (M8) wood screws, 2 3/4” (70mm) long Cement or brick - 1/4” (M6) stud expansion bolts, 3” (76mm) long Hollow wall - 1/4” (M6) toggle bolts, length depends on wall thickness 5. Run service wire to the dryer location and connect to t

Unit must be installed by a qualified licensed electrician. Do not connect any unit to a branch circuit over 20 amps. Dryers located in shower rooms or other wet locations should be equipped with ground fault interrupter(s). 6. Carefully replace the cover using tamper-proof bolts supplied. 1 1/4 1 (25 mm) (32 mm) 5/8 (17 mm) 9 1/2 (241 mm) DR Series Recess Mounted ROUGH OPENING 11 3/4” W (30cm) X 12 3/4” H 932cm) Operating Costs The only operating cost for the DR series hand dryer is electricity

DO NOT FORCE COVER OFF. 2. Dryers should be placed at least 2 feet (61cm) apart and at least 12” (30cm) from washbasin. Do not install dryers over washbasin. Hold the backplate to the wall at the suggested mounting height. Measure from bottom edge of backplate to the floor. 3. Mark the locations of the four mounting holes and the conduit entrance location on the wall. (The conduit entrance is the proper hole diameter for 1/2 inch (13mm) conduit.) 4. Fasten the backplate to the wall where previou

* 50 Hz for export only. Fixed Nozzle is an option on all models by designating (F) after model number. Recess Mounted is available on all models by designating (R) after model number or order kit separately (specify color). MECHANISM: •Motor Instant starting, maintenance-free, brushless motor. 1/10 HP, 3200 RPM, with self lubricating bearings. Protected by an automatic resetting circuit breaker. Our motor requires no fuses, oiling or brush replacement - 100% maintenance- free. Has considerably

Dryer shall deliver 160 CFM at 5500 LFM. Push button dryers shall be activated by a cam-operated mechanical timer. Cover shall be attached with one tamper-resistant bolt and a 3” steel latch which locks it securely to base. Tamper- resistant air intake vents, internal shield and side mounted heating element are for additional safety. Heating element is protected by an automatic resetting circuit breaker. Nozzle and push button shall be zinc die castings with a chrome plated finish. Nozzle shall

Element is not accessible through nozzle and is protected by an automatic resetting circuit breaker (thermostat). It produces an air temperature of 130-145.F at a 72.F ambient room temperature. FEATURES/MATERIALS: • Cover One piece industrial drawn 16 gauge reinforced steel or 18 gage reinforced type 304 stainless steel satin finish. • Finish Electrostatically applied white enamel or stainless steel satin finish. Resistant to chipping and cleaning agents. • Tamper-Resistant One tamper-resistant

42” (107cm) 40” (102cm) 30-40” (76-102cm) 34” (86cm) “DR-NH” Hair Dryer... 72” (183cm) 68” (173cm) 46-68” (117-173cm) 52” (132cm) Dimensions: WIDTH HEIGHT DEPTH NET WEIGHT Surface Mounted 11” 9-1/4” 6-5/8” 16 lbs. (7kg) Recessed Mounted 14-1/8” 14-1/8” 3-3/8” 23 lbs. (10kg) The dryer shall be manufactured by American Dryer to include a 16 gauge reinforced steel cover with a white enamel finish or 18 gage reinforced stainless steel cover with satin finish. Recessed units will include a 16 gauge s

Options include a stainless steel cover with satin finish, a fixed nozzle and recessed mounting. PUSH BUTTON HAND DRYING PUSH BUTTON HAIR DRYING AUTOMATIC HAND DRYING ELECTRICAL RATINGS Drying Drying Drying Model Cycle Model Cycle Model Cycle Volts Amps Watts Hertz DR10N 40 sec DR10NH 80 sec DR10TN Automatic 110-120 15 1725 60 DR20N 30 sec DR20NH 80 sec DR20TN Automatic 110-120 20 2300 60 DR30N 30 sec DR30NH 80 sec DR30TN Automatic 208-240 10 2300 60 DR50N 30 sec DR50NH 80 sec DR50TN Automatic 2

removal of cover: A) Loosen tamper-proof screws using wrench supplied, turn clockwise (donot remove). Located under bottom intake vent. B) To remove, place a hand on each side of cover and lift upward, then pull off. Dryers should be placed at least 2 feet (61cm) apart and at least 12” (30cm) 2. from washbasin. Do not install dryer over washbasin. Automatic dryers should be at least 18” (46cm) above any projection which may interfere with the operation of the automatic sensor. Hold the backplate