Votes - 3, Average rating: 4
(
)
)
|
manual abstract
DVD Playback only 60. COMPONENT VIDEO OUT Jacks Connect optional component video cables here and to the component Video In jacks of a television. 61. COAXIAL Jack Connect an optional coaxial digital audio cable here and to the Coaxial Digital Audio In jack of a decoder or audio receiver. 62. DVD ANALOG AUDIO OUT Jacks Connect the supplied audio cables here and to the Audio In jacks of a television or other audio equipment (DVD only). 63. S-VIDEO OUT Jack Connect an optional S-Video cable here and to the S- Video In jack of a television. (DVD only). 64. VIDEO IN Jack Connect a cable coming from the video out jack of a camcorder, another VCR, or an audio-visual source (laser disc player, video disc player, etc.) here. 65. DVD/VCR VIDEO OUT Jack Connect the yellow video cable (supplied) here and to the TV’s Video In jack. 66. ANT-OUT (Antenna Out) Jack Use the supplied RF cable to connect this jack to the ANTENNA IN Jack on your TV. Note .The S-VIDEO OUT jack, COAXIAL jack, and COM PONENT VIDEO OUT jack are only useful in DVD mode. Caution: Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the player. LOADING THE BATTERIES 1. Open the battery compartment cover. 2. Insert two AA batteries (supplied), with each one oriented correctly. 3. Close the cover. Notes .Do not mix alkaline and manganese batteries. .Do not mix old and new batteries. –11– EN 1L25 VCR/DVD SWITCHING Because this product is a combination of a VCR and DVD player, you must first select which component you wish to operate with the OUTPUT BUTTON. Press VCR on the remote control. (Verify that the VCR OUTPUT Light is lit.) VCR MODE Press DVD on the remote control. (Verify that the DVD OUTPUT Light is lit.) DVD MODE Note .Pressing only OUTPUT on the front panel does not switch the mode of the remote control. You always need to select the correct mode on the remote control too. OPEN/CLOSE OUTPUT REC REW FF VIDEO AUDIO CH-DOWN POWER CH-UP STOP/EJECT PLAY DV D VCR TIMER REC STOP PLAY DISC IN FWDREV PLAY OUTPUTDVD VCR OUTPUT button DVD OUTPUT Light DVD button VCR button VCR OUTPUT Light + 1 2 3 4 5 6 7 8 9 0 10 SPEED AUDIO POWER SKIP/CH. SLOW VCR/TV DISPLAY PAUSE PLAY STOP RECORD ENTER RETURNTITLE MENU SETUP CLEAR/ C.RESET ZOOMMODE A-BANGLE SEARCH MODE REPEAT SUBTITLE T-SET DVD VCR –12– EN 1L25 HOOKUPS CAUTION: .Be sure to turn off the DVD/VCR COMBINATION UNIT and equipment to be connected. .Read through the operation manual for the equipment to be connected. .Be sure that the colors of the jacks and plugs match up when using VIDEO/AUDIO cables. .Be sure to keep the DVD/VCR COMBINATION UNIT connection cables separate from the TV antenna cable when you install the DVD/VCR COMBINATION UNIT, because it may cause electrical interference when you are watching television programs. CONNECTING TO A TV WITHOUT A/V TERMINALS 1. Disconnect the AC power cord of the TV from the AC outlet. 2. Disconnect the antenna or cable from the TV. 3. Connect the antenna or cable to the ANT-IN jack of the DVD/VCR COMBINATION UNIT. 4. Connect the DVD/VCR COMBINATION UNIT to the TV using the RF cable. 5. Plug the AC power cords of the DVD/VCR COM[ VHF/UHF[Indoor antenna] [Back of the DVD/VCR] combination antenna] From Cable or Satellite Company [Cable box or satellite box] OR UHF/VHFANT-IN ANT-OUT VIDEO OUT AUDIO OUT VIDEO IN DVD/VCR VCR L [Back of the UHF/VHF combination TV] (supplied) RF cableOR BINATION UNIT and TV into the AC outlets. RF OUTPUT CHANNEL for DVD/VCR 1. Connect the DVD/VCR COMBINATION UNIT to a TV using RF cable (see above steps). 2. Select channel 3 on your TV. 3. Press PLAY. .If noise appears, change the RF output channel of the DVD/VCR COMBINATION UNIT to channel 4 by pressing PLAY on the VCR for 3 seconds during playback. .There is case that the RF output channel does not change by situation (For example, when you adjust tracking using SKIP/CH. (o/p) on the rimote or CH-(UP/DOWN) on the DVD/VCR COMBINATION UNIT). In this case, stop the playback, and start the playback again. After that, press PLAY on the VCR for 3 seconds. .If there is a power failure or the DVD/VCR COMBINATION UNIT is unplugged for more than 30 seconds, the RF output channel setting will return to CH3. Note to CATV system installer This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected to the grounding system of the building, as close to the point of cable entry as practical. CONNECTING TO A TV WITH A/V TERMINALS Antenna/Cable signal A/V-compatible or wide screen TV To Right (red) and Left (white) To AUDIO INPUT jacks To AUDIO OUT jacks [Fig. 1] ANT-IN AUDIO OUT S-VIDEO OUT AUDIO OUT DIGITAL AUDIO OUT COAXIAL Y Cb Cr L R COMPONENT VIDEO OUT DVD/VCR VCR DVD To VIDEO OUT jack To VIDEO INPUT jack To ANT. IN of TV Note .Connect the DVD/VCR COMBINATION UNIT directly to a T...