rated as being suitable for use with impact wrenches. - Prolonged exposure to vibration may cause injury. -Read all instructions before using this tool. Ail operators must be fully trained in its use and aware of these safety rules. - Do not exceed the maximum working air pressure. - Use personal protection equipment as recommended. - Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects and

Take off O-ring (44) and hook out oil seal (43) and press out anvil bushing (42) from housing (1). Grip hammer cage (34) and pull off the hammer mechanism assembly. Take off anvil spacer (38) and from hammer cage (34) pull out anvil (37). (45) or (50), spring (51) and thrust button (52). Push out 2 hammer pins (36) from hammer cage (34) to release 2 hammers (35) and carefully note how the two hammers (35) are located to hammer cage (34) by hammer pins (36) for reassembly). If replacements are re

It is always recommended that the tool is used when standing on the solid floor. It can be used in other positions, but before any such use, the operator must be in a secure position having a firm grip and footing and be aware that when loosening fasteners the tool can move quite quickly away from the fastener being undone. An allowance must always be made lor this rearward movement so as to avoid the possibility of handferm/body entrapment. Putting Into Service Air Supply Use a clean lubrica

When first lubricating a tool or if the tool exhaust has a high oil content, do not allow the exhaust air to come near very hot surfaces or flames. -Never lay the tool down until the working attachment has stopped moving. -When the tool is not in use, shut off the air supply and press throttle triggerllever to drain the supply line. If the tool is not to be used for a oeriod of time. first lubricate. disconnect from air supply &d store in a dry average room temperature environment. -If the tool

1 SAFETY MESSAGES 1 A WARNING 1 Operator Instructions PersonalSafety Equipment Always Read Instructions Before Includes:1 YES 1 0 "sing Power Tools 1 Use -Safety Glasses Safety Rules Use -Safety Gloves @ Always Wear Safety Goggles ores seen Use Work Stations Use -Safety Boots @ Wear Hearing Protection Putting Into Service Use -Breathing Masks A T Avoid Prolonged Exposure o Vibration Operating Use -Ear Protectors YES Disrnantlina and Assernblv. Safety rules when using a 509215092L Impact Tool -Us

If you do not have this equipment, you can not service this tool. Hypot testing is a safety test required by Underwriter’s Laboratories. It basically ensures that there are no live metal parts exposed on the product. This condition could occur if, for instance: 1. A housing screw went through a wire. 2. A wire was stripped back too far and the bare wire contacted a bearing or the driveshaft. 3. A wire was damaged and came into contact with a bearing or the driveshaft. This is a very serious

ImpactTool C? @ IMPORTANT Readtheseinstructionscarefullybefore installing,operating,servicing or repairingthis tool. Keeptheseinstructionsin a safeaccessible place. 11 I I I SAFETY MESSAGES 1 A WARNING 1 Operator Instructions PeoonalSafetyEqucment Always Read Instructions includes: 1 1 Use-Safety Glasses Using PowerTwls Safety Ruk Use -Safety Gloves @ AlwaysWear Safety Goggles Foreseen Use Work Stations Use-Safety Boots @ Wear Hearingprotection PuttingIntoService Use-BreathingMasks Avoid Prolong

No. Part No. Description 1 505372 Inlet Bushing with Screen 2 505709 Deflector 3 505371 O-RIng 4 505710 Valve Spring 5 505367 Valve 6 505366 Valve Pin 7 505365 Valve Seat 8 505713 Roll Pin 9 505867 Motor Housing 10 505868 Roll Pin 11 505869 Roll Pin 12 505870 Reverse Lever 13 505871 Spring 14 67202 Steel Ball 15 505711 Muflier 16 505714 Valve Shaft 17 505715 Trigger 18 67081 O-Ring 19 505872 Reverse Valve 20 505873 Ball Bearing Ref. No. Part No. Description 21 66570 Roll Pi