. When the battery is fully charged, the pilot lamp will bilink in red slowly. (At 1-second intervals) (See Table 2) Table 2 Lamp indications Indications of the pilot lamp Charge status lamp (RED) Before charging Blinks (RED) Lights for 0.5 seconds. Does not light for 0.5 seconds. (off for 0.5 seconds) While charging Lights (RED) Lights continuously Charging complete Blinks (RED) Lights for 0.5 seconds. Does not light for 0.5 seconds. (off for 0.5 seconds) Charging impossible Flickers (RED) Ligh
66 METODO DE EXTRACCION E INSTALACION DE LA BATERIA ............................................ 66 METODO DE CARGA .......................................... 66 ANTES DE LA UTILIZACION .............................. 70 OPERACION ........................................................ 70 ALCANCE Y SUGERENCIAS PARA LA UTILIZACION ................................................ 78 MANTENIMIENTO E INSPECCION ........................ 79 ACCESORIOS ..................................................
1. Switch operation The rotation speed of the drill bit can be controlled steplessly by varying the amount that the trigger switch is pulled. Speed is low when the trigger switch is pulled slightly and increases as the switch is pulled more. To turn the switch OFF, release the trigger switch to its original position. 2. Rotation + Striking This rotary hammer can be set to rotation and striking mode by pressing the push button and Fig. 6 turning the change lever to mark. (Fig. 6) (1) Mount the dr
7. NEVER operate without all guards in place. NEVER operate this tool without all guards or safety features in place and in proper working order. If maintenance or servicing requires the removal of a guard or safety feature, be sure to replace the guard or safety feature before resuming operation of the tool. 8. Use right tool. Don’t force small tool or attachment to do the job of a heavy-duty tool. Don’t use tool for purpose not intended —for example— don’t use circular saw for cutting tree lim
. Do not tighten too strongly as the screw heads will be damaged. English MAINTENANCE AND INSPECTION CAUTION: Pull out battery before doing any inspection or maintenance. 1. Checking the condition of the bit. The bits should be checked regularly. If worn or broken bits can slip or decrease the efficiency of the motor and burn it out. Replace worn bits with new ones. CAUTION: If you use a driver bit of which point is worn or broken, it will be dangerous since it slips. So replace it with a new on
English OPERATION 1. Mounting and dismounting of the bit (1) Mounting the bit. Insert a screwdriver bit etc. into the keyless drill chuck. Firmly grasp the ring and tighten the sleeve by turning it toward the right (in the clockwise direction as viewed from the front). (See Fig.5) NOTE: If the sleeve becomes loose during operation, tighten it further. The tightening force becomes stronger when the sleeve is tightened. Fig. 5 (2) Dismounting the bit. Firmly grasp the ring and loosen the sleeve by
For safe operations: 1. Keep work area clean. Cluttered areas and benches invite injuries. 2. Consider work area environment. Do not expose power tools to rain. Do not use power tools in damp or wet locations. Keep work area well lit. Do not use power tools where there is risk to cause fire or explosion. 3. Guard against electric shock. Avoid body contact with earthed or grounded surfaces. (e.g. pipes, radiators, ranges, refrigerators). 4. Keep children away. Do not let visitors touch the tool o
Please keep this manual available for others before they use the power tool. MODE D’EMPLOI ET INSTRUCTIONS DE SECURITE AVERTISSEMENT Une utilisation incorrecte et dangereuse de cet outil motorise peut entrainer la mort ou de serieuses blessures corporelles! Ce mode d’emploi contient d’importantes informations a propos de la securite de ce produit. Priere de lire et de comprendre ce mode d’emploi avant d’utiliser l’outil motorise. Garder ce mode d’emploi a la disponibilite des autres utilisateurs
Never carry charger by cord or yank it to disconnect from receptacle. Keep cord from heat, oil and sharp edges. 10. Secure work. Use clamps or a vise to hold work. It's safer than using your hand and it frees both hands to operate tool. 11. Don't overreach. Keep proper footing and balance at all times. 12. Maintain tools with care. Keep tools sharp at all times, and clean for best and safest performance. Follow instructions for lubricating and changing accessories. 13. When the charger is no
4. Wear a mask when turning your head upward. 5. Properly set the bit holder. 6. At the start of work, confirm screw tihghtening. 7. When working at a highly elevated location, pay attention to articles and persons below. 8. Wear portective shoes to protect your feet. 9. Make positively certain that you wear gloves when engaged in work for a long time since the grip can become very hot. 10. There is also a risk for a tool to be damaged, and therefore exercise utmost caution for any possible fall