The light will stop blinking in less time if the battery pack was not completely discharged. When needed, the internal fan of the charger will turn on to aid the charging process and speed. When charging several batteries in sequence, the charge time may slightly increase. When the battery pack is fully charged, unplug the charger (unless you're charging another battery pack) and slip the battery pack back into the tool. FIG. 12 BATTERY PACK RED LIGHT GREEN LIGHT -13- CHARGER BM 1619929800 12-07

A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may

If the green indicator light is “ON”, the charger is plugged in but the battery pack is not inserted, or the battery pack is fully charged. If the green indicator light is “BLINKING”, the battery pack is being fast-charged. Fast-charging will automatically stop when the battery pack is fully charged. If the red indicator light is “ON”, the battery pack is too hot or cold for fast-charging. The charger will automatically switch to fast-charging once a suitable temperature is reached. If the red i

The dust extraction system automatically switches on and off with the power tool. For maximum dust extraction efficiency, please observe the following. • The drill bit being used may not project beyond the dust cap as shown in figures 13 & 14. (Example for an SDS-plus drill bit: Max. total length approx. 160 mm, working length approx. 100 mm). • Pay attention that the dust cap faces flush against the workpiece or the wall. At the same time, this makes working at a right angle easier. • After rea

If you the hole or the tool is overloaded. Be aware experience bit binding and clutch begins to that due to required clutch setting, you may slip, immediately turn the tool "OFF" and experience a torque reaction an instant correct the condition leading to the bit before the clutch slips. This torque reaction binding. will twist the body of the rotohammer in the opposite direction as the bit rotates, i.e., AUXILIARY HANDLE Setting depth: After the auxiliary handle is The tool must be supported wi

If the green indicator light is “ON”, the charger is plugged in but the battery pack is not inserted, or the battery pack is fully charged and is being trickle charged, or the battery pack is too hot or cold for fast-charging. The charger will switch to trickle charge, until a suitable temperature is reached, at which time the charger will switch automatically to fast- charging. If the green indicator light is “BLINKING”, the battery pack is being fast-charged. Fast-charging will automatically s

Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. SAVE THESE INSTRUCTIONS Work area safety If operating the power tool in damp locations is unavoidable a Ground Fault Keep work area clean and well lit. Circuit Interrupter (GFCI) must be used to Cluttered or dark areas invite accidents. supply

To reduce the risk of injury, do not operate the Dymorig if the gauge reads less than 20 inches of mercury vacuum. WARNING! 6. Turn the Dymodrill motor ON. Turn the water on so it flows freely through the water shut-off valve (see "Supply an Adequate Water Flow"). Turn the valve clockwise to increase water flow and counterclockwise to decrease water flow. 7. While holding the handle, slightly loosen the cradle lock handle and slowly rotate the handle to lower the bit into the workpiece, applying

Contadores Cat. No. 48-51-0120 20 amperios, 120 volts (Se puede usar en Canada) El amperimetro y el interruptor de encendido aparecen en el panel frontal con un tomacorrientes sencillo de tipo de torsion de 20 amperios para el motor perforador en la parte posterior. Montaje de extension Cat. No. 49-95-1000 Este montaje refuerza el equipo entre el suelo y el techo para obtener la maxima rigidez. Se ajusta a techos de 4,3 m (14') y tiene ajustes de agujeros fijos. Arandela de cobre Cat. No. 45-88-

Avant de commencer le carottage, essayez de branler le berceau et la foreuse avec les mains. Si le berceau est correctement arrime, il ne bougera pas. Si, au contraire, il bouge, serrez les (6) boulons de reglette qui maintiennent le berceau en place sur le montant tel que decrit ci-dessous et illustre a la figure 7. Fig. 7 Boulons de reglette Pour les modeles 4125 et 4130 seulement. Serrez les six (12) boulons de reglette a l’aide de la cle hex. contenue dans le sac d’accessoires a part. 1. Pre