Votes - 3, Average rating: 3.7
(
)
)
|
manual abstract
• This power unit is intended to be correctly orientated in a vertical or floor mount position. SAVE THESE INSTRUCTIONS INTRODUCTION Black & Decker VPXTM chargers are designed to charge Black & Decker VPXTM battery packs in approximately 5-6 hours. The charger requires no adjustment and is designed to be as easy as possible to operate. Simply place your battery pack into the receptacle of a plugged in charger and it will automatically charge the pack. As you add new chargers to your Black & Decker VPXTM system, utilize the “daisy chain” feature to power multiple chargers from a single outlet. IMPORTANT SAFETY INSTRUCTION FOR BATTERY PACKS WARNING: For safe operation, read this manual and manuals originally supplied with tool before using the charger. The battery pack is not fully charged out of the carton. Before using the battery pack and charger, read the safety instructions below. Then follow charging procedures outlined. READ ALL INSTRUCTIONS • Do not incinerate the battery pack even if it is severely damaged or is completely worn out. The battery pack can explode in a fire. Toxic fumes and materials are created when lithium ion battery packs are burned. • Do not charge or use battery in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Inserting or removing the battery from the charger may ignite the dust or fumes. • If battery contents come into contact with the skin, immediately wash area with mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for 15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a mixture of liquid organic carbonates and lithium salts. • Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persists, seek medical attention. WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame. • Charge the battery packs only in Black & Decker VPXTM chargers. • DO NOT splash or immerse in water or other liquids. This may cause premature cell failure. • Do not store or use the tool and battery pack in locations where the temperature may reach or exceed 105°F (40.C) (such as outside sheds or metal buildings in summer). 7 90520993 VPX1201 VPX Dril#E4FEB 7/11/07 9:48 AM Page 8 WARNING: Never attempt to open the battery pack for any reason. Ifbattery pack case is cracked or damaged, do not insert into charger.Donot crush, drop or damage battery pack. Do not use a battery pack or charger that has received a sharp blow, been dropped, run over or damaged in any way (i.e., pierced with a nail, hit with a hammer, stepped on). Damaged battery packs should be returned to service center for recycling. WARNING: Fire hazard. Do not store or carry battery so that metal objects can contact exposed battery terminals. For example, do not place battery in aprons, pockets, tool boxes, product kit boxes, drawers, etc., with loose nails, screws, keys, etc. Transporting batteries can possibly cause fires if the battery terminals inadvertently come in contact with conductive materials such as keys, coins, hand tools and the like. The US Department of Transportation Hazardous Material Regulations (HMR) actually prohibit transporting batteries in commerce or on airplanes (i.e., packed in suitcases and carry-on luggage) UNLESS they are properly protected from short circuits. So when transporting individual batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit. STORAGE RECOMMENDATIONS 1. Always store batteries charged. 2. The best storage place is one that is cool and dry away from direct sunlight and excess heat or cold. 3. Recharge discharged batteries as soon as possible after use or battery life may be greatly diminished. CHARGING PROCEDURE 1. Plug the charger into an appropriate outlet before inserting the battery pack. 2. Insert the battery pack into the charger (figure B). Be sure the pack is fully seated in the charger. While charging, the red (charging) LED will flash continuously (slowly) indicating that the charging process has started. 3. The completion of charge is indicated by the red LED becoming solid. (approximately 5-6 hours) The pack is fully charged and may be used at this time or left on the charger. 4. Recharge discharged batteries as soon as possible after use or battery life may be greatly diminished. CHARGE INDICATORS Replace Pack: These chargers are designed to detect certain problems that can arise with battery packs which would be indicated by the red light flashing at a fast rate. If this occurs, re-insert battery pack. If problem persists, try a different battery pack to determine if the charger is OK. If the new pack charges correctly, then the original pack is defective and should be returned to a service center for recycling. If the new battery pack gives the same trouble indication as the original, have ...