Votes - 4, Average rating: 4.3
(
)
)
|
Other manuals for this model:
Musical Instruments - M3000-24 (116.01 kb)
Musical Instruments - M3000-24 (114.47 kb)
Musical Instruments - M3000-24 (114.48 kb)
manual abstract
However even in this case, you can turn on the AFL switch (6) to monitor the pre-fader signal from the MONITOR OUT jacks or the PHONE jack. A l In check mode B You can use the CHECK indicators to view the on/off status of each MIX OUT stored in a scene before you C actually recall the scene. In check mode, you can also use the ON/EDIT switches to change only the lit/dark status of the CHECK indicators. (The actual on/off setting will not be affected.) For details on check mode, refer to page 33. E Mix master faders These faders adjust the output level of MIX OUT 1– D 16. These faders affect the signal which is sent to the MIX OUT 1–16 jacks, the MAS AFL bus, the ST bus, and the matrix. EF AFL (after fader listen) switches These switches allow the signals from MIX OUT to be monitored from the MONITOR OUT jacks or PHONES jack. When these switches are on ( ), the pre-fader signal of the corresponding MIX bus will be F sent to the MAS PFL bus, and the post-fader signal will be sent to the MAS AFL bus, allowing you to monitor from the MONITOR OUT jacks or the PHONES jacks. The signal of the MAS AFL bus can be monitored when the MASTER PFL switch (page 19) of the monitor section is off, and the signal of the MAS PFL bus can be monitored when this switch is on. However while even one of the PFL switches of the input channels is on, the signal of the PFL bus will take precedence, meaning that it will not be possible to monitor MIX OUT. Control panel 15 MIX buses 1–8 MIX buses 9–12 MIX buses 13–16 (SUB)(ST) from INPUT MIX 3-4, 5-6, 7-8: Same as MIX 1-2 MIX 2: Same as MIX 1 to Meter VARIABLE FIX PFLAFL L R ON MAS AFL MAS (MIX) TO MATRIX CONTROL CHECK ON ON/EDIT MIX OUT 1 AFL PAN TO STEREO TO MATRIX MIX INSERT I/O ST L R L R MIX (FIX) MIX (VARIABLE) 1 3 5 7 1 2 3 4 5 6 7 8 2 4 6 8 9 11 13 15 10 12 14 16 from..Ctrl Master 1 3 5 7 2 4 6 8 9 11 13 15 10 12 14 16 L R L R (SUB)(ST) PFLAFL L R ON MAS AFL MAS (MIX) TO MATRIX ST L R L R MIX (FIX) MIX (VARIABLE) 1 3 5 7 1 2 3 4 5 6 7 8 2 4 6 8 9 11 13 15 10 12 14 16 1 3 5 7 2 4 6 8 9 11 13 15 10 12 14 16 L R L R from ST CH from Ctrl Master ON/EDIT CHECK ON CONTROL MIX 10, 11, 12: Same as MIX 9 to Meter TO MATRIX PAN TO STEREO AFL MIX OUT 9 MIX INSERT I/O (SUB)(ST) PFLAFL L R ON MAS AFL MAS (MIX) TO MATRIX ST L R L R MIX (FIX) MIX (VARIABLE) 1 3 5 7 1 2 3 4 5 6 7 8 2 4 6 8 9 11 13 15 10 12 14 16 1 3 5 7 2 4 6 8 9 11 13 15 10 12 14 16 L R L R from Ctrl Master CONTROL CHECK ON ON/EDIT MIX 15-16: Same as MIX 13-14 to Meter AFL TO MATRIX BAL TO STEREO MIX OUT 14 MIX INSERT I/O MIX INSERT I/O MIX OUT 13 Control panel Control panel n The VCA master fader section allows the gain of input channels assigned to a VCA group to be controlled as a whole by the corresponding VCA fader. The VCA group(s) to which each input channel is assigned is specified by the VCA GROUP select switches (mono input channels (U), stereo input channels R). MIX 1/2 10 MIX 3/4 MIX 5/6 MIX 7/8 MIX 9/10 MIX 11/12 MIX 13/14 MIX 15/16 10 10 10 10 10 10 10 VCA MUTE VCA MUTE5 VCA MUTE5 VCA MUTE5 VCA MUTE5 VCA MUTE5 VCA MUTE5 VCA MUTE55 0 0 0 0 0 0 0 0 NOMINAL NOMINAL NOMINAL NOMINAL NOMINAL NOMINAL NOMINAL NOMINAL 5 10 20 30 40 50 60 5 10 20 30 40 50 60 5 10 20 30 40 50 60 5 10 20 30 40 50 60 5 10 20 30 40 50 60 5 10 20 30 40 50 60 5 10 20 30 40 50 60 5 10 20 30 40 50 60 A B C A VCA MUTE switches When these switches are turned on (the indicator at left will light), the VCA master fader (3) will be shut down completely. At this time, the post-fader signal of STEREO A section all input channels assigned to the corresponding VCA group will be muted. This section controls the signal that is output from the rear panel ST OUT jacks (page 28). The signal level B NOMINAL indicators which is sent from ST OUT A to the matrix is also These indicators will light when the corresponding controlled by this section. VCA master fader is in the nominal (0 dB) position. In this position, the VCA master fader will not affect (MIX) TO MATRIX (SUB)(ST) 1 3 5 7 9 111315 LR LR the gain. C VCA master faders These faders control the gain of the input channels ST assigned to the corresponding VCA group. If you wish LR to use the VCA master faders, make sure that the rear panel VCA MASTER/SLAVE select switch (page 28) is set to the MASTER position. ST INSERT I/O L ST INSERT I/O R ON ON/EDIT CHECK ON CONTROL to Meter to Meter ON AFL AFL TO MATRIX AFLPFLLR ON MAS AFL MAS LR PFL LEVEL ST OUT B L R R L ST OUT A RL 2 4 6 8 10 12 14 16 to MONITOR OUT to PHONES Control panel 10 5 0 5 10 20 30 40 50 60 STEREO A TO MATRIX ON/EDIT AFL CHECK ON STEREO A A D C B Control panel 10 5 0 5 10 20 30 40 50 60 STEREO A TO MATRIX ON/EDIT AFL CHECK ON STEREO A A D C B A TO MATRIX switch When this switch is on ( ), the ST OUT A post- fader signal is sent to the matrix. B ON/EDIT switch The function of this switch and indicator will depend on the mode of the M3000. l In normal mode The ON/EDIT switch will turn ST OUT A on/off. When on, the ON indicator will light. When...
Other models in this manual:Musical Instruments - M3000-40C (680.69 kb)